manualshive.com logo in svg

Suzuki DF150AP, Owner'S Manual

Share
Download
Suzuki DF150AP Owner'S Manual Download Page 88

88

Inspect and clean the fuel filter as follows:

1. Turn the engine off and allow it to cool.
2. If equipped with Keyless Start System:

Make sure that the keyless start system is in
OFF stage.

If not equipped with Keyless Start System:
Make sure that the main switch is in the OFF
position.

3. Remove the bolts 

1

 securing the resonator

2

 in place.

4. Remove the resonator 

2

.

5. Push the connector lock tab “a”, then discon-

nect the water sensor lead wire connector

3

.

6. Place a rag under the filter before removal to

catch any spilled fuel.

7. Separate the filter cup 

4

 from the cap 

5

 by

turning the filter cup counterclockwise.

NOTICE

Improperly loosening the filter cup can
cause sensor lead wire damage.

• Be careful not to twist the sensor lead

wire when removing the filter cup.

• Disconnect the lead wire connector

before removing the filter cup.

“a”

Summary of Contents for DF150AP












































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands