manualshive.com logo in svg

Suzuki DF150AP, Owner'S Manual

Share
Download
Suzuki DF150AP Owner'S Manual Download Page 14

14

SUB BATTERY CABLE

The sub battery cable 

1

 is used to supply volt-

age to the engine control system. In the midst
of the cable, a 30A fuse 

2

 is provided to pro-

tect the control circuit.
If the sub battery cable is not correctly con-
nected to the battery, engine cannot be started.

DUAL BATTERY CHARGING SYSTEM

If installing the battery isolator lead assembly,
available as optional parts, and changing the
position of 30A fuse from standard to option,
dual battery charging system will be effective.
Be sure to check if the 30A fuse in OPT position
is blown, when the second battery for accesso-
ries will not be charged. 
Please ask your authorized Suzuki Marine
Dealer for installation of the isolator lead
assembly.

NOTICE

The electrical system or its components
may be damaged if proper battery pre-
cautions are not followed.

• Be sure to attach battery leads cor-

rectly.

• Do not disconnect battery leads from

the battery while the engine is running.

USE OF ELECTRICAL ACCESSORIES

The amount of power (12V DC) available for
accessories depends on the operating condi-
tion of the motor. For detail information, please
contact an authorized Suzuki Marine Dealer.

NOTE:
Use of too much power for electrical accesso-
ries under certain operating conditions can
cause the battery to discharge.

Summary of Contents for DF150AP












































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands