background image

38

To make a bevel rip cut.

 WARNING: When making a bevel rip cut, 

the rip fence must be on the right side of the 
blade to avoid trapping the wood and causing 
kickback. Placement of the rip fence to the left 
of the blade will result in kickback and the risk 
of serious personal injury.

 WARNING: Make sure the blade guard as-

sembly is installed and working properly to 
avoid serious personal injury.
• Remove the miter gauge by sliding it out of 
the miter gauge groove.
• Turn the bevel locking lever to the left to un-
lock. Turn the blade adjusting handle until the 
bevel indicator is at the desired angle.
• Set the blade to the correct depth for the 
workpiece and push the bevel locking lever to 
the right to relock it.
Position the rip fence the desired distance from 
the right side of the blade and lock down the 
lever.
• Place a support the same height as the table 
surface behind the saw for the cut work.
• Make sure the wood is clear of the blade be-
fore turning on the saw.
• Turn the saw ON.
• Position the workpiece flat on the table with 
the edge flush against the rip fence. Let the 
blade build up to full speed before feeding the 
workpiece into the blade.
• Using a push stick and/or push blocks, slowly 
feed the workpiece toward the blade. Stand 
slightly to the side of the wood as it contacts 
the blade to reduce the chance of injury should 
kickback occur.
• Once the blade has made contact with the 
workpiece, use the hand closest to the rip 
fence to guide it. Make sure the edge of the 
workpiece remains in solid contact with both 
the rip fence and the surface of the table. If 
ripping a narrow piece, use a push stick to 
move the piece through the cut and past the 
blade.

To make a bevel cross cut

 WARNING: Make sure the blade guard as-

sembly is installed and working properly to 
avoid serious personal injury.

• Remove the rip fence by depressing the lock 
and lifting the locking handle.
• Turn the bevel locking lever to the left to un-
lock it. Turn the blade adjusting handle until 
the bevel indicator is at the desired angle.
• Set the blade to the correct depth for the 
workpiece and retighten the bevel locking le-
ver.
• Set the miter gauge at 90° and tighten the 
miter gauge lock knob.
• Place a support (the same height as saw ta-
ble) behind the saw for the cut work.
• Make sure the wood is clear of the blade be-
fore turning on the saw.
• Turn the saw ON.
• Let the saw blade build up to full speed be-
fore moving the workpiece into the blade.
• Hold the workpiece firmly with both hands on 
the miter gauge and feed the workpiece into 
the blade. Keep the workpiece flush against 
the miter gauge. Stand slightly to the side of 
the wood as it contacts the blade to reduce the 
chance of injury should kickback occur.
NOTE: The hand closest to the blade should be 
placed on the miter gauge lock knob and the 
hand farthest from the blade should be placed 
on the workpiece.
• When the cut is made, turn the saw OFF. Wait 
for the blade to come to a complete stop be-
fore removing any part of the workpiece.

Bevel Cross Cut

Bevel Rip Cut

SM710 manual2.indd   38

04/08/16   12:24 p.m.

Summary of Contents for SM710













































Reviews: