16
7. Pull the trigger on the gun to start water
jetting: • Stand on a stable surface and grip gun/
spray wand firmly with both hands. • Expect the
gun to kick when the trigger is pulled.
8. Release trigger to stop water flow.
The machine with a signal lamp:
Overload Signal: When
machine output overload,
the light will on.
Release Gun Signal: when the
high-pressure gun is spray on,
the signal light is on; When
the high-pressure gun is spray
off, the signal light is off.
Oil Change(on)/ Low Voltage(Flash) Signal:
flashing for 2 seconds, low voltage.
Oil Change(on)/Low Voltage(Flash) Signal: light
on for long time: The crankshft pump need to
change oil. After changing the oil, press the
“stop” button for long time, and the signal light
will turn off. The signal light will turn on each
time when machine use each 50 hours.
** Oil Change(on)/Low Voltage(Flash) Signal
lights only indicate the use time, can not fully
show the crankshaft pump oil level, before each
use please check the tripple pump oil level, if
the oil level is lower, please add 15W-40 oil in
time.
Once the instrument work for the machine
protections, please take off the power plug
from the socket, and put in again to restart
the machine . NOTE: The power washer will
automatically go into bypass mode.
WARNING: DO NOT ALLOW UNIT TO
OPERATE IN BYPASS MODE FOR MORE THAN
TWO MINUTES AT ANY TIME. OVERHEATING OF
PUMP CAN CAUSE DAMAGE TO PUMP.
USING THE SPRAY NOZZLE TIPS
Follow these instructions to change spray tips:
1. Engage trigger lock on spray gun.
2. Pull back collar on quick-connect and pull
current spray tip off.
3. Select desired spray tip:
For gentle rinse, select white 40 or green 25
spray tip. To scour surface, select yellow 15 or
red 0 spray tip.
4. Pull back on collar, insert new spray tip and
release collar. Tug on spray tip to make sure it is
securely in place.
5. For most effective cleaning, keep spray tip
from 8 to 24 inches away from cleaning surface.
6. DO NOT get closer than 6 inches when
cleaning automobile tires.
Spray Tips
SPRAY NOZZLE MAINTENACE
A pulsing sensation felt while squeezing the
spray gun trigger may be caused by excessive
pump pressure. The principal cause of excessive
pump pressure is a nozzle clogged or restricted
with foreign materials, such as dirt, etc. To
correct the problem, immediately clean the
nozzle.
ADJUSTING THE PRESSURE
The pressure setting is preset at the factory. To
lower the pressure:
1. Adjust the pressure regulator on the pump.
Turn the pressure regulator knob counter
clockwise to lower pressure. Once you have
finished using your power washer, return the
pressure regulator to its original position.
2. Back away from the surface to be cleaned.
The further away you are the less the pressure
will be on the surface being cleaned.
3. Adjust the spray to a wider angle.
RECOMMENDED CLEANING PROCEDURE
Turn on the water supply tap FULLY. Release the
safety catch, then press the trigger for a few
seconds to allow air to escape and to discharge
residual pressure in the pipes.
Dissolve dirt by applying detergent with the fan
jet to the dry surface. On vertical surfaces, work
from the bottom upwards.
Leave the detergent to act for 1 to 2 minutes,
but do not allow to dry out. Apply the high
pressure jet, keeping the nozzle at least 10” (30
cm) from the surface, working from the bottom
upwards. Avoid allowing the rinsing water to
run on to unwashed surfaces.
WARNING: Always test the spray in an area
free and clear of people and objects before you
sprayat the intended cleaning surface.
WOOD AND VINYL DECKS
Rinse deck and surrounding area with fresh wa-
ter. If using detergent, fill the detergent reser-
voir and apply to the area being cleaned at low
pressure. For optimal results, reduce your work
Blanco
40°
Verde
25°
Amarillo
15°
BOQUILLAS DE ALTA PRESIÓN
Rojo
Point Jet