Sure Heat T87PHLP Page 13 Use And Care Manual Download | Manualshive

Page: 13 / 22

background image

Assembly Process

13

Slide one Small Flat Washer over threaded end of screw and loosely screw on Cap Nut. Repeat

procedure to complete the assembly of all three Reflector Panel sections.

Slide Reflector Plate onto Reflector Panels.

Insert one Small Screw.

Slide one small Flat Washer over threaded end

of screw and loosely screw on Cap Nut. Repeat

procedure to install the remaining screws.

Once all screws have been loosely installed, tighten all screws with a wrench.

«
...
11
12
13
14
15
...
»

Summary of Contents for T87PHLP























Reviews:

No comments

Related manuals for T87PHLP

Brand: B-TEC Pages: 11

Brand: Zip Pages: 18

Brand: Takagi Pages: 60

Brand: Zodiac Pages: 12

Brand: EUROM Pages: 116

Brand: Orava Pages: 19

Brand: TDM Pages: 28

Brand: Cadet Pages: 6

Brand: Lynx Pages: 22

Brand: Toyotomi Pages: 25

Brand: Consort Pages: 4

Brand: Hanover Pages: 19

Brand: Wacker Neuson Pages: 68

Brand: Ballu Pages: 11

Brand: UNITED Pages: 9

CN 04 050 EIS W

Brand: TESY Pages: 148

OUT370609/PH100T

Brand: Outback Pages: 16

Brand: Nippa Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands