Sure Heat Manufacturing Altima AGR30PF Use And Care Manual Download Page 19

LIGHTING THE GRILL

AGR48PF Grill Burner Lighting

This unit comes equipped with (2) electronic starters
and (4) electrodes.  The electronic starter located on
the right shelf lights the Bottom Infrared Burner
which is controlled by Knob #1 and the Right Main
Burners, which are controlled by Knobs 2 & 3.  The
electronic starter on the left shelf lights the Left Main
Burners, which are controlled by Knobs 4,5 & 6.  The
left electronic starter also lights the Back Infrared
Burner. 

Always open the lid before attempting lighting.  
Push and turn one of the control knobs a 

1/4

turn to

the left and immediately press the electronic ignitor
button.  You’ll hear a snapping sound.  It may be nec-
essary to hold the electronic starter button for about 4
seconds.  If the burner does not light in 4 seconds,
turn the knob to the “OFF” position and wait 5 min-
utes before trying again.  Repeat above steps to light
remaining burners. (See Fig. 15)

Match Lighting

If the burner does not light after several attempts it
may be lit with a match.  Keep your face as far away
from the grill surface as possible and pass a lit, long
stem match through the spaces in the grill rack to the
ports of the burner you are trying to light.  Position
the match near the burner ports and push and turn the
control knob a 

1/4

turn to the left.  If the burner does

not light within 4 seconds turn the knob to the “OFF”
position and wait 5 minutes to try again. Repeat
above steps to light remaining burners. (See Fig. 16)

17

Right electric starter
For Bottom Infrared
Burner & Main Burners
#2 & #3

Left electric starter
For Main Burners #4, #5
& #6 and Back Infrared
Burner

Back
Infrared

Knob

#6

Knob

#5

Knob

#4

Knob

#3

Knob

#2

Knob

#1

Fig. 15

Fig. 16

Note:

If the grill will not light after several 

attempts see the Troubleshooting section of
this manual.

Turn the control knobs to the OFF position
when not in use.

Summary of Contents for Altima AGR30PF



























Reviews: