background image

Heatseeker UniPanel®

 

Solar Pool Heating

12

Pump Faults

Ensure the controller has working sensors; otherwise the pump will not operate.

FAULT

REASONS/SOLUTIONS

PUMP WILL NOT START

The pump will only ever run for the purpose of automatic heating if the pool is below the

temperature limit and solar conditions can provide heating. The pump may also run for a 

flush in standby mode or for manual mode operation. If the controller reports that the pump 

is off, then press select to enable manual mode. The relay inside should click and the pump 

should operate. If the pump does not operate, then plug the pump into a power point and 

test operation. If the pump is okay, then the controller requires repair.

PUMP WILL NOT STOP

Turn off power to the controller and ensure the pump stops. If the pump continues to operate, 

then unplug it from the power point and connect it to the 240V socket marked PUMP at the 

bottom of the controller.
Apply power to the controller and if the pump starts instantaneously before temperatures are 

displayed, then there may be a fault with the controller. Since the controller shouldn’t run when 

there is a sensor fault, disconnect the roof sensor and wait for approximately 30 seconds. If the 

pump continues to run, then the controller requires repair.

POOL NOT HEATING

If the controller has stopped pumping and is displaying a higher temperature than expected, it 

may be caused by a pump which is failing to prime. Check the pump and if necessary prime the 

pump as per the pump manufacturers’ instructions then reset the controller by turning it off/on.

RTC-FAIL

This can occur if the unit has been turned off for a prolonged period of time. Leave the unit on 

for 30 seconds and this will allow charging of the supercapacitor. Next, turn it off for 30 seconds 

before turning it back on.

Summary of Contents for Heatseeker UniPanel

























Reviews: