suprema XPass D2 Installation Manual Download Page 14

  FCC  compliance  information 

FCC  compliance  information 

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.   
Operation is subject to the following two conditions: 
(1) This device may not cause harmful interference, and 
(2) This device must accept any interference received, including interference that may cause undesired operation. 
 
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the 
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. 
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the 
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not 
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be 
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the 
following measures: 

 

Reorient or relocate the receiving antenna. 

 

Increase the separation between the equipment and receiver. 

 

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 

 

Consult the dealer or an experienced radio/TV technician for help. 

Modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment under FCC 
rules.   
 
 

This appliance and its antenna must not be co-located or operation in conjunction with any other antenna or transmitter. 
A minimum separation distance of 20 cm must be maintained between the antenna and the person for this appliance to satisfy 
the RF exposure requirements. 

 
 

EU  Declaration  of  Conformity  (CE)   

This product is CE marked according to the provisions of the Radio Equipment Directive (RED) 2014/53/EU. Hereby, Suprema Inc. 
declares that this product is in compliance with the essential requirements and other relevant provisions of Radio Equipment 
Directive (RED) 2014/53/EU. 
 

 

Bluetooth Transmit Power: -0.44 dBm 

 

Bluetooth Frequency: 2402~2480 MHz 

 

NFC Frequency: 13.56 MHz 

 

RFID Frequency: 13.56 MHz + 125 kHz 

 
For more information, contact us at the following contact information. 
Suprema Inc. 
Website

https://www.supremainc.com

 

Address: 17F Parkview Tower, 248, Jeongjail-ro, Bundang- gu, Seongnam-si, Gyeonggi-do, 13554, Rep. of KOREA 
Tel: +82-31-783-4502 / Fax: +82-31-783-4503 
 
 
 

 

Summary of Contents for XPass D2

















Reviews: