1. TECHNICAL SPECIFICATIONS
SWIVEL STOVE
PACCO / P. HAUT / P. SUR PIED / P.
BÛCHER
Stove category
Intermittent
Rated heat output (1)
10 kW
Operating mode
Only with the door closed
Connection type
Vertical
Mean flue gas temperature
314 °C
Efficiency
78 %
Seasonal efficiency
68 %
CO concentration (13 % 02)
0.10 %
CO2 concentration (13 % 02)
10.37 %
Dust concentration (13 % 02)
18 mg/Nm
3
.
COV
99 mg/Nm3
NOX
105 mg/Nm3
Fuel
Wood
Log size
50 cm.
Nominal load per hour approx.
2.9 kg
Refuelling
45 min.
Prohibited fuels
All the rest, including coal and its
derivatives
Approx. flue gas mass flow
7.2 g/sec
Fluepipe nominal diameter
150 mm.
Flue pipe specifications
Minimum dimensions of the chimney terminal
20 x 20 cm
Ø mín flue lining or insulated metal duct
150 mm.
Minimum height of the pipe above the
appliance
4 m.
Ventilation of the room
1.2 dm²
Draught (10 Pa = 1 mm CE)
Nominal efficiency
12 Pa ± 2 Pa
Performance in slumber mode (min. permitted)
6 Pa ± 1 Pa
Max. permitted
20 Pa
Nameplate
On the rear of the appliance
Accessorires supplied
Grippers; Insulating glove
Option available
AT15 Draught adaptor
(1) Rated power in operation with the door closed, wood or lignite fuel, according to the tests performed under standard EN 1 3240.
(2) DTU 24.1 covering flue ducting, DTU 24.2 covering chimneys equipped with a closed stove; NIF EN 13240 covering solid fuel burning
stoves. (Available at AFNOR).
- IMPORTANT -
You have just purchased a wood burning stove from our range. We would first like to congratutate you on your choice. This app liance
has been carefully designed. In order to make the most of all its advantages, we would advise you to request the services of one of our
specialists. This will ensure that the installation is made in accordance with good practices and will guarantee the best operating and
safety conditions, bearing all the responsibility for the final installation.
Before lighting the fire for the first time, please read these installation instructions and user manual carefully. Retain th e manual and
warranty (which indicates the model and serial No.). The person performing the installation work shall be fully responsible for any failure
to comply with the instructions set out in these documents.
- IMPORTANT ASSEMBLY INSTRUCTIONS -
Your stove has a "good draw" but you do not know its draught value. The chimney draught is measured in Pascal (Pa). The
inserts, fireboxes and stoves have been designed, optimised and manufactured in accordance with standards NF EN 13229 (or
NF EN 13240) to operate connected to a chimney with a draught of 12 Pa. It frequently happens (in more than one in two
chimneys) that the draught is far too high (over 20 Pa) due to the fact that the chimney is either too high or due to the flu e
liner. In this case, the appliances will operate in abnormal conditions which may lead to:
- Excessive wood consumption: this can be three times as much as an appliance with a draught of 12 Pa.
- A fire that "does not last" and burns too quickly while producing insufficient heat.
- A quick and inevitable deterioration of the appliance (cracks in the cast iron panels or in the refractory bricks)
- A voided warranty.
To avoid all these problems, there is only one solution!
Get a professional to check the chimney draught (with the appliance operating) and, if it is above 20 Pa, then install a damper
or an adaptor at the flue connection.