background image

Chapter 7: BIOS

7-5

Bootup Num-Lock

This feature selects the Power-on state for Numlock key.  The options are Off 

and 

On

.

PS/2 Mouse Support

This feature enables support for the PS/2 mouse.  The options are Disabled, 

Enabled and 

Auto.

Wait For 'F1' If Error

This forces the system to wait until the 'F1' key is pressed if an error occurs.  The 

options are Disabled and 

Enabled

.

Hit 'Del' Message Display

This feature displays "Press DEL to run Setup" during POST.  The options are 

Enabled

 and Disabled. 

Watch Dog Function

If enabled, the Watch Dog Timer will allow the system to reboot when it is inactive 

for more than 5 minutes. The options are Enabled and 

Disabled.

Power Button Function

This setting allows you to decide if the power button will turn off the system in-

stantly or wait for 4 seconds when it is pressed. The options are  

Instant Off

 and 

4 Seconds Override.

Restore on AC Power Loss

Use this feature to set the power state after a power outage. Select Power-Off for 

the system power to remain off after a power loss. Select Power-On  for the system 

power to be turned on after a power loss. Select Last State to allow the system to 

resume its last state before a power loss. The options are Power-On, Power-Off

 

and 

Last State

.

Interrupt 19 Capture

Interrupt 19 is the software interrupt that handles the boot disk function. When this 

item is set to Enabled, the ROM BIOS of the host adaptors will "capture" Interrupt 

19 at boot and allow the drives that are attached to these host adaptors to function 

as bootable disks. If this item is set to Disabled, the ROM BIOS of the host adap-

tors will not capture Interrupt 19, and the drives attached to these adaptors will not 

function as bootable devices. The options are 

Enabled

 and Disabled. 

Summary of Contents for Supero SUPERSERVER 5015A-EHF-D525



























































































Reviews: