background image

AOC-SASLP-MV8 Add-on Card User’s Manual

ii

The information in this User’s Manual has been carefully reviewed and is believed to be accurate. The 
vendor assumes no responsibility for any inaccuracies that may be contained in this document, makes no 
commitment to update or to keep current the information in this manual, or to notify any person or 
organization of the updates. 

Please Note: For the most up-to-date version of this manual, please see 

our web site at 

www.supermicro.com

.

Super Micro Computer, Inc. (“Supermicro”) reserves the right to make changes to the product described 
in this manual at any time and without notice. This product, including software, if any, and documentation 
may not, in whole or in part, be copied, photocopied, reproduced, translated or reduced to any medium or 
machine without prior written consent.

IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL, 
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO USE 
THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH 
DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, 
SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE COSTS OF 
REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH HARDWARE, 
SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa Clara 
County in the State of California, USA. The State of California, County of Santa Clara shall be the 
exclusive venue for the resolution of any such disputes. Super Micro's total liability for all claims will not 
exceed the price paid for the hardware product.

FCC Statement: This equipment has been tested and found to comply with the limits for a Class A digital 
device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection 
against harmful interference when the equipment is operated in a commercial environment. This 
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in 
accordance with the manufacturer’s instruction manual, may cause harmful interference with radio 
communications. Operation of this equipment in a residential area is likely to cause harmful interference, 
in which case you will be required to correct the interference at your own expense.

California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warning 
applies only to products containing CR (Manganese Dioxide) Lithium coin cells. Perchlorate 
Material-special handling may apply. See 

www.dtsc.ca.gov/hazardouswaste/perchlorate

 for further 

details.

Manual Revison 1.0a

Release Date: March 10, 2009

Unless you request and receive written permission from Super Micro Computer, Inc., you may not copy 
any part of this document. Information in this document is subject to change without notice.

Copyright © 2008 by Super Micro Computer, Inc.
All rights reserved.

Printed in the United States of America

WARNING: 

HANDLING OF LEAD SOLDER MATERIALS USED IN THIS 

PRODUCT MAY EXPOSE YOU TO LEAD, A CHEMICAL KNOWN TO THE 
STATE OF CALIFORNIA TO CAUSE BIRTH DEFECTS AND OTHER 
REPRODUCTIVE HARM.

Summary of Contents for Supero AOC-SASLP-MV8





















Reviews: