Supero SUPER P3TDLR User Manual Download | Manualshive

Page: 67 / 90

background image

Chapter 7: BIOS/Setup

4-21

BIOS

4-7

Power Setup

Choose "Power Setup" from the AMIBIOS Setup main menu. All Power

Setup options are described in this section. The Power Setup screen is

shown below.

ACPI Aware O/S

This option allows the system to utilize Intel's ACPI (Advanced Configuration

and Power Interface) specification. Settings are No and Yes. DOS®,

Windows 3.x®, and Windows NT® are examples of non-ACPI aware oper-

ating systems.

Windows 95®, Windows 98® and Windows 2000® are

examples of ACPI aware operating systems.

Power Management

This option allows you to select using APM (Advanced Power Manage-

ment). The settings are Disabled and Enabled.

Power Button Mode

This option specifies how the external power button on the computer chas-

sis functions. When set to On/Off, depressing the power button turns the

computer on or off. When set to "Suspend", depressing the power button

places the computer in Suspend mode or Full On power mode. The Standby

setting places the computer in Standby or Full On mode.

BIOS SETUP UTILITY

Main Advanced Chipset PCIPnP Power Boot Security Exit

ACPI Aware O/S
Power Management
Power Button Mode
Sleep Button Enable
Green PC Monitor Power State
Video Power Down Mode
Hard Disk Power Down Mode
Inactivity Timer
Suspend Timeout (Minutes)
IRQ1
IRQ3
IRQ4
IRQ5
IRQ6
IRQ7
IRQ9
IRQ10
IRQ11
IRQ12
IRQ14
IRQ15

[Yes]
[Enabled]
[On/Off]
[Suspend]
[StandBy]
[Suspend]
[Disabled]
[Off]
[Off]
[Monitor]
[Ignore]
[Ignore]
[Ignore]
[Ignore]
[Ignore]
[Ignore]
[Ignore]
[Ignore]
[Monitor]
[Monitor
[Ignore]

↔

Select Screen

↑↓

Select Item

+- Change Option
F1 General Help
F10 Save and Exit
ESC Exit

V02.03 (C)Copyright 1985-2000, American Megatrends, Inc.

«
...
65
66
67
68
69
...
»

Summary of Contents for SUPER P3TDLR



























































































Reviews:

No comments

Related manuals for SUPER P3TDLR

MachXO5-NX Development Kit

Brand: Lattice Semiconductor Pages: 64

Brand: Sleipner Pages: 28

Brand: Freetech Pages: 79

Brand: ASROCK Pages: 56

Brand: Biostar Pages: 23

Brand: Ublox Pages: 22

Brand: Abit Pages: 110

Brand: ASRock Industrial Pages: 41

Brand: Acconeer Pages: 14

Brand: DFI Pages: 177

P4 Titan GA-8SIMLH-P

Brand: Gigabyte Pages: 104

Brand: JETWAY Pages: 54

Brand: Acorp Pages: 26

Brand: DFI Pages: 110

Brand: DFI Pages: 124

Brand: ASROCK Pages: 6

Brand: Suzuki Pages: 3

Brand: IEI Technology Pages: 158

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands