Supero AS2021M-UR Plus User Manual Download Page 64

Page: 64 / 104

6-2

AS2021M-UR+ User's Manual

Figure 6-1. Front and Rear Chassis Views

System Reset

6-2 Control

Panel

The control panel (located on the front of the chassis) must be connected to the

JF1 connector on the serverboard to provide you with system status indications. A

ribbon cable has bundled these wires together to simplify the connection. Connect

the cable from JF1 on the serverboard to the Control Panel PCB (printed circuit

board). Make sure the red wire plugs into pin 1 on both connectors. Pull all ex-

cess cabling out of the airﬂ ow path. The LEDs inform you of system status. See

Chapter 3 for details on the LEDs and the control panel buttons. Details on JF1

can be found in Chapter 5.

Control Panel

Main Power

Slim DVD-ROM Drive

3.5" Drive Bays (2)

Hard Drive Bays (8)

Floppy Drive (optional)

Ethernet Ports

USB Ports

Keyboard/Mouse Ports

COM1 Port

PCI Add-on Card Slots

VGA Port

USB Ports (2), COM Port

Summary of Contents for AS2021M-UR Plus









































































































Search results

Summary of Contents for AS2021M-UR Plus

Reviews:

Supero AS2021M-UR Plus, User Manual, Page: 64 / 104

Search results

Summary of Contents for AS2021M-UR Plus

Reviews: