Supermicro SUPERSERVER 1028TR-T Page 128 User Manual Download

Page: 128 / 144

7-30

SUPERSERVER 1028TR-T/TF User's Manual

4-4 Event Logs

Use this feature to confi gure Event Log settings.



Change SMBIOS Event Log Settings

This feature allows the user to confi gure SMBIOS Event settings.

Enabling/Disabling Options

SMBIOS Event Log

Select Enabled to enable SMBIOS (System Management BIOS) Event Logging

during system boot. The options are

Enabled

and Disabled.

Runtime Error Logging Support

Select Enable to support Runtime Error Logging. The options are

Enable

and

Disable. If this item is set to Enable, the following item will be available for

confi guration:

Summary of Contents for SUPERSERVER 1028TR-T

















































































































































Search results

Summary of Contents for SUPERSERVER 1028TR-T

Reviews:

Related manuals for SUPERSERVER 1028TR-T

Brands by name

Popular brands

Supermicro SUPERSERVER 1028TR-T, User Manual

Search results

Summary of Contents for SUPERSERVER 1028TR-T

Reviews:

Related manuals for SUPERSERVER 1028TR-T

Brands by name

Popular brands