Chapter 6: BIOS
77
76
SuperServer 1019S-MC0T User's Manual
Port 0 ~ Port 7 SATA Device Type
Use this item to specify if the SATA port specified by the user should be connected to a Solid
State drive or a Hard Disk Drive. The options are
Hard Disk Drive
and Solid State Drive.
PCIe/PCI/PnP Configuration
The following information will display:
•
PCI Bus Driver Version
•
PCI Devices Common Settings:
PCI Latency Timer
Use this feature to set the latency Timer of each PCI device installed on a PCI bus. Select
32 to set the PCI latency to 32 PCI clock cycles. The options are
32 PCI Bus Clocks
, 64
PCI Bus Clocks, 96 PCI Bus Clocks, 128 PCI Bus Clocks, 160 PCI Bus Clocks, 192 PCI Bus
Clocks, 224 PCI Bus Clocks, and 248 PCI Bus Clocks.
PCI-X Latency Timer
Use this feature to set the latency Timer of each PCI-X device installed on a PCI bus. Select
64 to set the PCI latency to 64 PCI clock cycles. The options are 32 PCI Bus Clocks,
64 PCI
Bus Clocks
, 96 PCI Bus Clocks, 128 PCI Bus Clocks, 160 PCI Bus Clocks, 192 PCI Bus
Clocks, 224 PCI Bus Clocks, and 248 PCI Bus Clocks.
PCI PERR/SERR Support
Select Enabled to allow a PCI device to generate a PERR/SERR number for a PCI Bus Signal
Error Event. The options are
Disabled
and Enabled.
Above 4G Decoding (Available if the system supports 64-bit PCI decoding)
Select Enabled to decode a PCI device that supports 64-bit in the space above 4G Address.
The options are
Disabled
and Enabled.
SR-IOV Support
Use this feature to enable or disable Single Root IO Virtualization Support. The options are
Disabled
and Enabled.
PCH SLOT4 PCI-E 3.0 X2 (IN X4) OPROM
Use this feature to select which firmware type to be loaded for the add-on card in this slot.
The options are Disabled,
Legacy
, and EFI.
CPU SLOT6 PCI-E 3.0 X8 OPROM
Use this feature to select which firmware type to be loaded for the add-on card in this slot.
The options are Disabled,
Legacy
, and EFI.
Onboard 10G LAN Option ROM Type
Use this item to select the Onboard 10G LAN Option ROM type. The options are Disabled,
Legacy,
and EFI.
Onboard SAS Option ROM
Select Enabled to enable SAS Option ROM support to boot the computer using a SAS device
specified by the user. The options are Disabled,
Legacy,
and EFI.
Onboard Video Option ROM
Use this item to select the Onboard Video Option ROM type. The options are Disabled,
Legacy,
and EFI.
Network Stack
Select Enabled to enable PXE (Preboot Execution Environment) or UEFI (Unified Extensible
Firmware Interface) for network stack support. The options are Disabled and
Enabled
.
IPv4 PXE Support
Select Enabled to enable IPv4 PXE boot support. The options are Disabled and
Enabled
.
IPv6 PXE Support
Select Enabled to enable IPv6 PXE boot support. The options are
Disabled
and Enabled.
PXE boot wait time
Use this option to specify the wait time to press the ESC key to abort the PXE boot. Press
"+" or "-" on your keyboard to change the value. The default setting is
0
.
Media detect count
Use this option to specify the number of times media will be checked. Press "+" or "-" on your
keyboard to change the value. The default setting is
1
.
Super IO Configuration
The following Super IO information will display:
•
Super IO Chip AST2400
Super IO Chip Logical Device(s) Configuration
Serial Port 1
Serial Port 1 Configuration
This submenu allows the user the configure settings of Serial Port 1.
