Chapter 6: BIOS
75
74
SuperServer 1019S-M2 User's Manual
Port 61h bit-4 Emulation
Select Enabled to enable the emulation of Port 61h bit-4 toggling in SMM (System Management
Mode). The options are Disabled and
Enabled
.
PCIe PLL SSC
Enable this feature to reduce EMI interference by down spreading clock 0.5%. Disable this
feature to centralize the clock without spreading. The options are
Disabled
and Enabled.
SATA Configuration
When this submenu is selected, the AMI BIOS automatically detects the presence of the SATA
devices that are supported by the Intel PCH chip and displays the following items:
SATA Controller(s)
This item enables or disables the onboard SATA controller supported by the Intel PCH chip.
The options are
Enabled
and Disabled.
SATA Mode Selection
Use this item to select the mode for the installed SATA drives. The options are
AHCI
and RAID.
SATA Frozen
Use this item to enable the HDD Security Frozen Mode. The options are Enabled and
Disabled
.
*If the item above "SATA Mode Selection" is set to RAID, the following items will
display:
SATA RAID Option ROM/UEFI Driver
Select UEFI to load the EFI drvier for system boot. Select Legacy to load a legacy driver
for system boot. The options are
Legacy ROM
and UEFI Driver.
SATA Port 0 ~ Port 3
This item displays the information detected on the installed SATA drive on the particular
SATA port.
•
Model number of drive and capacity
•
Software Preserve Support
Port 0 ~ Port 3 Spin Up Device
On an edge detect from 0 to 1, set this item to allow the PCH to initialize the device. The
options are Enabled and
Disabled
.
Port 0 ~ Port 3 SATA Device Type
Use this item to specify if the SATA port specified by the user should be connected to a Solid
State drive or a Hard Disk Drive. The options are
Hard Disk Drive
and Solid State Drive.
PCIe/PCI/PnP Configuration
The following information will display:
•
PCI Bus Driver Version
•
PCI Devices Common Settings:
PCI PERR/SERR Support
Select Enabled to allow a PCI device to generate a PERR/SERR number for a PCI Bus Signal
Error Event. The options are Enabled and
Disabled
.
Above 4G Decoding (Available if the system supports 64-bit PCI decoding)
Select Enabled to decode a PCI device that supports 64-bit in the space above 4G Address.
The options are Enabled and
Disabled
.
PCH SLOT4 PCI-E 3.0 X4 (IN X8)
Use this feature to select which firmware type to be loaded for the add-on card in this slot.
The options are Disabled,
Legacy
, and EFI.
CPU SLOT6 PCI-E 3.0 X16
Use this feature to select which firmware type to be loaded for the add-on card in this slot.
The options are Disabled,
Legacy
, and EFI.
PCH SLOT 7 PCI-E 3.0 X4 (IN X8)
Use this feature to select which firmware type to be loaded for the add-on card in this slot.
The options are Disabled,
Legacy
, and EFI.
Onboard LAN Option ROM Type
Select Enabled to enable Option ROM support to boot the computer using a network device
specified by the user. The options are
Legacy
and EFI.
Onboard LAN1 Option ROM
Use this option to select the type of device installed in LAN Port1 used for system boot. The
default setting for LAN1 Option ROM is
PXE
.
Onboard LAN2 Option ROM
Use this option to select the type of device installed in LAN Port2 used for system boot. The
default setting for LAN2 Option ROM is
Disabled
.
