Supermicro SBI-7147R-S4F User Manual Download Page 35

Page: 35 / 84

3-5

Chapter 3: Setup and Installation

Caution:

Refer to the Supermicro website for updates on CPU support.

There are two load levers on the LGA2011 socket. To open the socket cover, first
press and release the load lever labeled 'Open 1st' (

Figure 3-3

Press the second load lever labeled 'Close 1st' to release the load plate that covers
the CPU socket from its locking position (

Figure 3-4

Figure 3-3. Open First Load Lever

Figure 3-4. Close First Load Lever

OPEN 1st

OPEN

1st

WARNING!

WAR

NIN

Press down on Load
Lever labeled 'Open

OPEN 1st

OPEN

1st

WARNING!

WAR

NIN

OPEN 1st

OPEN

1st

RNIN

WAR

NIN

OPEN 1st

OPEN

1st

WARNING!

WAR

NIN

Press down on
Load the Lever
labeled 'Close 1st'

Pull lever away from the socket

Summary of Contents for SBI-7147R-S4F





















































































Search results

Summary of Contents for SBI-7147R-S4F

Reviews:

Related manuals for SBI-7147R-S4F

Brands by name

Popular brands

Supermicro SBI-7147R-S4F, User Manual

Search results

Summary of Contents for SBI-7147R-S4F

Reviews:

Related manuals for SBI-7147R-S4F

Brands by name

Popular brands