background image

 

1

3.Re wiring according to 
instructions. 

The gate can open but 
cannot close. 

1.Photocell wiring with problem. 
2.Photocell mounting with problem. 
3.Photocell is blocked by objects. 
4.Auto-reverse force is too small. 
 

1.If not connect photocell, please 
make sure that the infrared port 
and GND short circuit; if connect 
infrared sensor, please make sure 
the wiring is correct and the 
photocell is N.C. 
2.Make sure that the photocell 
mounting position can be mutually 
aligned. 
3.Remove the obstacle. 
4.Increase auto-reverse force. 

Remote control doesn’t 
work. 

1.Battery level of the remote 
control is low 
2.Remote control learning is not 
completed 

1.Change the remote control 
battery 
2.Re-conduct remote control 
learning 

Press OPEN, CLOSE 
button, the gate is not 
moving, motor has 
noise. 

1.Capacitor is broken. 
2.Capacitor is poor connected. 
3.Gate moving is not smoothly. 

1.Change capacitor. 
2.Check the capacitor wiring. 
3.According to the actual situation 
to adjust the motor or the gate. 

Not stop at the limit 
position when opening / 
closing. 

1. The limit direction is wrong. 
2. The mounting of magnetic limit 
switch with problem. 

1.Check whether the limit switch 
wiring is consistent with the actual 
direction of operation.   
2. Check whether the distance 
between magnetic limit switch and 
motor, and the height of the 
magnetic limit switch can meet the 
mounting requirement. 

Leakage switch tripped. 

Power supply line short circuit or 
motor line short circuit.   

Check wiring. 

Remote control working 
distance is too short. 

Signal is blocked. 

Connect external receiver 
antenna, 1.5 meters above 
ground. 

The gate moves to the 
middle position to stop 
or reverse. 

1.Motor output force is not enough. 
2.Auto-reverse force is not enough. 
3.Gate meets obstacle. 

1.Adjust the VR2. 
2.Adjust the VR3. 
3.Remove the obstacle. 

Gate opens 
automatically 

Automatic close function has been 
turned on but with incorrect 
opening direction. 

Please refer to the attentions 
under 4.3.5 “DIP switch 
adjustment”, to change the 
opening direction through DIP 
switch 5. 

 

Summary of Contents for SSLG-2 800DC




















Reviews: