background image

Danaher Motion Superior Electric

SS2000MD4 

400030-043 Rev G

Safety 

Safety symbols used in this manual are: 

 

Warning

 Alerts users to potential physical danger or harm. Failure to follow 

warning notices could result in personal injury or death. 

 

Caution

 Directs attention to general precautions, which if not followed, could result 

in personal injury and/or equipment damage. 

 

Note

 Highlights information critical to your understanding or use of the product. 

Instructions 

Only qualified personnel should install or perform servicing procedures on this equipment. 

Do not 

operate the unit without the enclosures in place as voltage present in this unit can cause serious or 
fatal injury. 

Before performing any work on the unit, allow at least five minutes for the capacitors to 
discharge fully. 

Voltage is present on unprotected pins when unit is operational. 

The "PWR ON" LED must be off for approximately 30 seconds before making or breaking 
the motor connections. 

Motors powered by these drives may develop extremely high torque. Disconnect AC power to 
these drive before doing any mechanical work. 

 

This unit is designed for 115 VAC input only (see Section 4.2, 
Electrical Specifications).

 

Warranty And Limitation Of Liability

 

Danaher Motion (the "Company") warrants to the first end user purchaser (the "purchaser") of 
equipment manufactured by the Company that such equipment, if new, unused and in original 
unopened cartons at the time of purchase, is free from defects in material and workmanship under 
normal use and service for a period of one year from date of shipment from the Company's factory or 
a warehouse of the Company in the event that the equipment is purchased from the Company or for a 
period of one year from the date of shipment from the business establishment of an authorized 
distributor of the Company in the event that the equipment is purchased from an authorized 
distributor. 

THE COMPANY'S OBLIGATION UNDER THIS WARRANTY SHALL BE STRICTLY AND 

EXCLUSIVELY LIMITED TO REPAIRING OR REPLACING, AT THE FACTORY OR A SERVICE 

CENTER OF THE COMPANY, ANY SUCH EQUIPMENT OR PARTS THEREOF WHICH AN 

AUTHORIZED REPRESENTATIVE OF THE COMPANY FINDS TO BE DEFECTIVE IN MATERIAL 

OR WORKMANSHIP UNDER NORMAL USE AND SERVICE WITHIN SUCH PERIOD OF ONE 

YEAR. THE COMPANY RESERVES THE RIGHT TO SATISFY SUCH OBLIGATION IN FULL BY 

REFUNDING THE FULL PURCHASE PRICE OF ANY SUCH DEFECTIVE EQUIPMENT

. This 

warranty does not apply to any equipment which has been tampered with or altered in any way, 
improperly installed or has been subject to misuse, neglect or accident. 

Summary of Contents for SLO-SYN SS2000MD4





































Reviews: