![background image](http://html1.mh-extra.com/html/roland/cd-01a/cd-01a_owners-manual_1479334001.webp)
*
5
1
0
0
0
0
3
2
7
4
-
0
1
*
USB CD Drive
CD-01A Owner’s Manual
Thank you, and congratulations on your choice of the Roland CD-01A USB CD Drive.
The CD-01A is a CD drive designed to be used exclusively with Roland products. It should not be used with
personal computers or equipment produced by other manufacturers.
Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT
NOTES” (other side). These sections provide important information concerning the proper operation of
the unit. Additionally, in order to feel assured that you have gained a good grasp of every feature
provided by your new unit, Owner’s Manual should be read in its entirety. The manual should be saved
and kept on hand as a convenient reference.
Copyright © 2008 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in any form without the written
permission of ROLAND CORPORATION.
Panel Descriptions and Contents of the Package
CD Drive Unit
* Depending on the circumstances of a particular setup, you may experience a discomforting sensation, or perceive that the
surface feels gritty to the touch when you touch this device. This is due to an infinitesimal electrical charge, which is
absolutely harmless. However, if you are concerned about this, connect the ground terminal (see figure) with an external
ground. When the unit is grounded, a slight hum may occur, depending on the particulars of your installation. If you are
unsure of the connection method, contact the nearest Roland Service Center, or an authorized Roland distributor, as listed
on the “Information.”
Unsuitable places for connection
• Water pipes (may result in shock or electrocution)
• Gas pipes (may result in fire or explosion)
• Telephone-line ground or lightning rod (may be dangerous in the event of lightning)
Connecting to the Equipment
* To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power
on all devices before making any connections.
* When connecting the CD-01A, be sure to read the connection instructions and cautions on connection in the owner’s
manual for the equipment to which you’re connecting the CD-01A.
Switching On the Power
* Once the connections have been completed, turn on power to your various devices in the order specified. By turning on
devices in the wrong order, you risk causing malfunction devices.
1.
Set the power switch to “AUTO.”
2.
Switch on the power to the equipment you’re using.
The CD-01A is interlinked with the equipment’s power, and
comes on automatically when the equipment is switched on.
* Depending on the equipment that the CD-01A is connected to, the power to it may not be switched on automatically. In
such cases, manually set the CD-01A’s power switch to the “ON” position.
Inserting and Ejecting Discs
When inserting a disc, make sure the CD-01A is powered up, and
gently insert the disc into the disc slot. Once the disc has been
inserted a certain distance, it is automatically pulled the rest of the
way into the drive.
To take out the disc, press the Eject button.
* This unit cannot use discs of nonstandard shape.
* If pressing the Eject button fails to eject the disc, do not try using force
to remove it. Instead, contact the nearest Roland Service Center, or an
authorized Roland distributor, as listed on the “Information.”
Installing on the Equipment
1.
Attach the mounting plates to the drive unit.
* Attachment requires a Phillips screwdriver. You will need to provide this yourself.
2.
Install the CD-01A on the equipment.
Check the model name of the equipment you’re using.
AC adaptor
Power Cord
Mounting
Plate (2 pcs.)
USB cable
Screw
(3 x 8 mm: 4 pcs.)
Screw
(4 x 16 mm: 4 pcs.)
Access Lamp
Eject Button
Disc Slot
Front Panel
Ground Terminal
Rear Panel
Power Switch
AC Adaptor Jack
Cord Hook
USB Connector
Security Slot ( )
http://www.kensington.com/
(full-size drawing)
(full-size drawing)
To prevent the inadvertent disruption of power to
your unit (should the plug be pulled out
accidentally), and to avoid applying undue stress
to the AC adaptor jack, anchor the power cord
using the cord hook, as shown in the illustration.
Place the AC adaptor so the side with
the indicator (see illustration) faces
upwards and the side with textual
information faces downwards.
The indicator will light when you plug
the AC adaptor into an AC outlet.
USB Cable
AC Adaptor
Power cord
To the AC Outlet
To the USB Connector on the Equipment
Power Switch
Screw
(3 x 8 mm)
Compatible Models and Installation Locations
* Installation on equipment not in the list of compatible models is not possible.
* Above table shows compatibility as of Oct. 2008. The latest information is listed for you on our website.
http://www.roland.com/
Installation Method A
3.
Using the included screws, install the drive unit in
the mounting holes (4 locations) on the underside of
the equipment.
4.
Connect the USB cable for the CD drive to the USB
connector for CD-drive connection on the
equipment.
* Before you make the connection, be sure to read the documentation for
the equipment to which you’re connecting.
Installation Method B
3.
Using a Phillips screwdriver, remove the
rubber foot on the left side and toward the
front on the underside of the equipment
where you’re installing this unit.
4.
Detach the headphones hook and reattach
it at the location shown in the figure.
5.
Using the included screws, install the drive
unit in the mounting holes (2 locations) on
the underside of the equipment.
* Carefully store the removed screws and rubber foot in a
safe place out of the reach of small children, so there is no
chance of them being swallowed accidentally.
6.
Connect the USB cable for the CD drive to
the USB connector for CD-drive connection on the equipment.
* Before you make the connection, be sure to read the documentation for the equipment to which you’re connecting.
Compatible
model name
DP-990, HPi-7S, HPi-6S, HP207, HP203, RG-3,
RG-1, RK-300, AT-900, AT-900C, AT-800,
AT-500, AT-300, AT-100, AT-75
FP-7
Installation
location
Install on the right side. Install as described in
“Installation Method A.”
Install on the left side. Install as described in
“Installation Method B.”
Screw
(4 x 16 mm)
Screw (4 x 16 mm)
3. Rubber Foot
4.
Headphones
Hook
This product complies with the requirements of EMC Directive 2004/108/EC.
For EU Countries
For Canada
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
NOTICE
AVIS
For the USA
FEDERAL COMMUNICATIONS COMMISSION
RADIO FREQUENCY INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Unauthorized changes or modification to this system can void the users authority to operate this equipment.
This equipment requires shielded interface cables in order to meet FCC class B Limit.
WARNING
This product contains chemicals known to cause cancer, birth defects and other reproductive harm, including lead.
For C.A. US (Proposition 65)
For EU Countries