background image

4

Installation and Operation Instructions

900300-00, 01/2018

Innovative Hearth Products
DRT35ST and DRT35PF Direct-Vent Gas Fireplaces

TABLE OF CONTENTS 

Packaging .........................................Page 4

Introduction ......................................Page 4

General Information ..........................Page 4

Requirements for the 

   Commonwealth of Massachusetts .Page 6

Cold Climate Insulation .....................Page 7

Manufactured Home Requirements ..Page 7

Location ............................................Page 7

Vent Termination Clearances  ............Page 8

Appliance and Vent Clearances .........Page 8

Detailed Installation Steps .................Page 11

Typical Installation Sequence  ...........Page 11

Step 1. Framing .................................Page 12

Fireplace and Framing Specifications .Page 13

Step 2. Routing Gas Line ..................Page 15

Step 3. Appliance Vent Collar ............Page 15

Step 4. Install The Venting System ...Page 16

Vertical Termination Systems ............Page 17

Vent Section Length Chart ................Page 17

Vertical Vent Tables and Figures ........Page 19

Horizontal Termination System .........Page 22

Horizontal Vent Tables and Figures ...Page 24

Venting Using Flexible Vent Pipe .......Page 27

Step 5.  Field Wiring .........................Page 28

Step 6.  Optional Blower Kit Wiring ..Page 29

Step 7.  Connecting Gas Line ...........Page 30

Step 8.  Verifying Appliance Operation Page 31

Step 9.  Installing Logs  ...................Page 33

Step 10. Remove/Install Glass Door  .Page 35

Step 11. Burner Adjustments ............Page 35

Step 12. Hood Installation .................Page 37

Finishing Requirements ....................Page 37

Step 13. Attaching Safety-in- 

    Operation Warnings ................. Page 38

Installation Accessories ....................Page 39

Gas Conversion Kits .................. Page 41

Operation/Care of Your Appliance .....Page 47

Gas Controls Access .........................Page 47

Variable Flame Adjustment ................Page 48

Attaching Safety in 

    Operation Warnings ......................Page 49

Maintenance ......................................Page 50

Front Glass Enclosure Panel,

  Removal and Installation .................Page 51

Install Vermiculite, Embers 

   and Logs ........................................Page 51

Burner Flame Appearance/Sooting ....Page 55

Burner Flame Adjustments ................Page 56

Millivolt Appliance Checkout .............Page 56

Electronic Appliance Checkout ..........Page 56

Wiring Diagrams ...............................Page 57

Accessory Components ....................Page 58

Maintenance Schedule ......................Page 59

Lighting Instructions – Millivolt ........Page 60

Lighting Instructions – Electronic .....Page 63

Troubleshooting Guide – Millivolt......Page 64

Troubleshooting Guide – Electronic ..Page 65

Replacement Parts List .....................Page 66

Warranty ...........................................Page 69

Please read and understand these 

instructions before beginning your 

installation.

PACKAGING

The  assembled vented gas fireplace heater  is 

packaged with:

1 - the logs are packaged in a carton located 

within the firebox.

2  -  one plastic bag of glowing embers is located 

in the bottom compartment.

3 - one poly bag containing the literature 

package which consists of Installation and 

Operation manual, Hot Glass Safety Flyer, 

and Safety-In-Operation Warning Labels, 

8 (DRT35ST) and 4 (DRT35PF) nailing 

flanges, on/off rocker switch and wire 

harness; poly bag is located in the bottom 

compartment.

4  -  one vent restrictor to be applied as shown on 

Page 14

;

 restrictor is taped to the envelope. 

5 -  two hoods on see-through units and three 

hoods on peninsula fireplaces.

6 -  top standoffs taped to top of unit.

7 -  front face assemblies with barriers.

NOTE:

•  If the barrier becomes dam-

aged, the barrier shall be re-

placed with the manufacturer’s 

barrier for this appliance.

•  For use with barrier(s) Part 

No(s). J7424 (ST Models) and 

J7424 and J7425 (PF Models).

INTRODUCTION 

The 

Millivolt

 appliances have a millivolt gas 

control valve with piezo ignition system. If any 

optional accessories that will require electrical 

power are to be installed, the electrical power 

must be provided at the time of appliance 

installation. 

The 

Electronic

 appliances are designed to op-

erate on natural or propane gas. An electronic 

intermittent pilot ignition system provides safe, 

efficient operation. External electrical power is 

required to operate these units. 

These vented gas fireplace heaters are sealed 

combustion, air-circulating gas fireplaces de-

signed for residential applications. 

Approved Vent Components

 - These fireplaces 

are designed, tested and listed for operation 

and installation with the following vent com-

ponents only:  

   

Secure Vent

®

 Direct-Vent System Compo-

nents manufactured by IHP, 

   

Secure Flex

®

 Flexible Vent Components 

manufactured by IHP and 

   

Z-FLEX

®

 Model GA Venting Systems listed 

to UL1777 and ULCS635 manufactured by 

Flexmaster Canada Limited. 

Use only the correct size venting (4-1/2" inner 

and 7-1/2" outer).

These approved vent system components are 

labeled for identification. DO NOT use any 

other manufacturer’s vent components with 

these appliances.  

Children and adults should be alerted to the 

hazards of high surface temperature and 

should stay away to avoid burns or clothing 

ignition. 

Les enfants et les adultes devraient être infor-

més des dangers que posent les températures 

de surface élevées et se tenir à distance afin 

d’éviter des brûlures ou que leurs vêtements 

ne s’enflamment.

DO NOT ATTEMPT TO ALTER OR MODIFY 

THE CONSTRUCTION OF THE APPLIANCE OR 

ITS COMPONENTS.  ANY MODIFICATION OR 

ALTERATION MAY  VOID THE WARRANTY, 

CERTIFICATION AND LISTINGS OF THIS UNIT.

       WARNING 

Young children should be care-

fully supervised when they are 

in the same room as the appli-

ance. Toddlers, young children 

and others may be susceptible 

to accidental contact burns.  A 

physical barrier is recommended 

if there are at risk individuals in 

the house.  To restrict access to 

a fireplace or stove, install an 

adjustable safety gate to keep 

toddlers, young children and 

other at risk individuals out of 

the room and away from hot 

surfaces.

       AVERTISSEMENT 

Les jeunes enfants devraient être 

surveillés étroitement lorsqu’ils 

se trouvent dans la même pièce 

que l’appareil. Les tout petits, 

les jeunes enfants ou les adultes 

peuvent subir des brûlures s’ils 

viennent en contact avec la sur-

face chaude.  Il est recommandé 

d’installer une barrière physique 

si des personnes à risques habi-

tent la maison.  Pour empêcher 

l’accès à un foyer ou à un poêle, 

installez une barrière de sécu-

rité; cette mesure empêchera les 

tout petits, les jeunes enfants et 

toute autre personne à risque 

d’avoir accès à la pièce et aux 

surfaces chaudes.

GENERAL INFORMATION

 

Summary of Contents for DRT35PF







































































Reviews: