background image

8

IN-RF-P-GEN4-001

Liability Statement

SuperATV’s

®

 products are designed to best fit user’s ATV/UTV under stock conditions. Adding, modifying, or fabricating any factory or aftermarket parts will void any warranty 

provided by SuperATV

®

 and is not recommended. SuperATV’s

® 

products could interfere with other aftermarket accessories. If user has aftermarket products on machine, contact 

SuperATV

®

 to verify that they will work together.

Although SuperATV

®

 has thousands of satisfied customers, user should be aware that installing lift kits, long travel, or suspension kits, tires, etc. will change the ride of machine 

and may increase maintenance and part wear. Operating any off-road machine while, or after, consuming alcohol and/or drugs increases risk of bodily harm or death. No 

warranty or representation is made as to this product’s ability to protect user from severe injury or death. SuperATV

®

 urges operators and occupants to wear a helmet and 

appropriate riding gear at all times.
By purchasing and installing SuperATV

®

 products, user agrees that should damages occur, SuperATV

®

 will not be held responsible for loss of time, use, labor fees, replacement 

parts, or freight charges. SuperATV

®

, nor any 3rd party, will not be held responsible for any direct, indirect, incidental, special, or consequential damages that result from any 

product purchased from SuperATV

®

. The total liability of seller to user for all damages, losses, and causes of action, if any, shall not exceed the total purchase price paid for the 

product that gave rise to the claim.
SuperATV

®

 will warranty only parts provided by SuperATV

®

. Any damage or problems with OEM housings, bearings, seals, or other manufacturers’ products will not be covered 

by SuperATV

®

. SuperATV

®

 parts and products are not warrantied if item was not installed properly, misused, or modified.

Installing, adding, modifying, or fabricating any factory or aftermarket product to your ATV/UTV may violate certain local, state, and federal laws. Be advised that laws vary 

depending on town, city, county, state, etc. Use of certain products on public streets, roads, or highways may be in violation law. The Buyer is solely and exclusively legally and 

personally responsible for any violation of the law by the installation or use of the product. You must abide by all local, state, and federal laws, including but not limited to vehicle 

safety, traffic laws, and ordinances. It is your responsibility to know the laws and how they apply to you. 
The Buyer is responsible to fully understand the capability and limitations of his/her vehicle according to manufacturer specifications, warnings and instructions and agrees to 

hold SuperATV

®

 harmless from any damage resulting from failure to adhere to such specifications, warnings and/ or instructions. The Buyer is also responsible to obey all 

applicable federal, state, and local laws and ordinances when operating his/her vehicle while using this product, and the Buyer agrees to hold SuperATV

®

 harmless from any 

violation thereof.

Summary of Contents for RF-P-GEN4-001









Reviews: