Super X8DT6 User Manual Download Page 72

Page: 72 / 99

4-10

X8DT6/X8DT6-F/X8DTE/X8DTE-F

User’s Manual

Crystal Beach/DCA (Direct Cache Access)

This feature works in conjunction with the Intel I/O AT (Acceleration Technology) to

accelerate the performance of the TOE device. When this feature set to Enabled, it

will enhance overall system performance by providing direct cache access for data

transferring. The options are Enabled and

Disabled.

NUMA Support

Select Enabled to use the feature of Non-Uniform Memory Access to improve CPU

performance. The options are

Enabled

and Disabled.

Payload Size

This feature limits the payload size by enabling (128B) or disabling (256B) coalesce

support. The options are 256B and

128B

Intel VT-d

Select Enabled to enable Intel Virtualization Technology support for Direct I/O VT-d

by reporting the I/O device assignments to VMM through the DMAR ACPI Tables.

This feature offers fully-protected I/O resource-sharing across the Intel platforms,

providing the user with greater reliability, security and availability in networking and

data-sharing. The settings are Enabled and

Disabled



SouthBridge Confi guration

This feature allows the user to confi gure the settings for the Intel ICH South

Bridge.

USB Functions

Select Enabled to use onboard USB ports. The Options are: Disabled and

Dis-

abled

Legacy USB Support

Select Enabled to use Legacy USB devices. If this item is set to Auto, Legacy USB

support will be automatically enabled when a legacy USB device is installed on the

motherboard. The settings are Disabled, and

Enabled

USB 2.0 Controller Mode

This setting allows you to select the USB 2.0 Controller mode. The options are

Hi-Speed (480 Mbps

) and Full Speed (12 Mbps).

BIOS EHCI Hand-Off

Select Enabled to enable BIOS Enhanced Host Controller Interface support to

provide a workaround solution for an operating system that does not have EHCI

Summary of Contents for X8DT6




































































































Search results

Summary of Contents for X8DT6

Reviews:

Related manuals for X8DT6

Brands by name

Popular brands

Super X8DT6, User Manual

Search results

Summary of Contents for X8DT6

Reviews:

Related manuals for X8DT6

Brands by name

Popular brands