manualshive.com logo in svg

Super Systems PGA 3510, Operation Manual, Page: 36 / 42

Share
Download
Super Systems PGA 3510 Operation Manual Download Page 36

PGA 3510 Operations Manual 

Super Systems Inc.                      

 

 

 

Page 36 of 42 

 

 

 

3.

 

Prepare the temperature sourcing device. This device should be capable of sourcing a 

temperature from type “S” and type “K” thermocouple types. 

4.

 

Connect the thermocouple wire from the temperature sourcing device to the appropriate input on 

the side of the case. 

5.

 

Enter the desired temperature value based on which to deliver a corresponding voltage. 

6.

 

Configure the temperature sourcing device to deliver the proper voltage. 

7.

 

Wait for the “Current Value” displayed on the screen to get as close to the target voltage as 

possible. 

8.

 

Tap Calibrate. Tap “Yes” when asked if you want to proceed with the calibration. A progress 

indicator will appear. 

9.

 

When the process completes, temperature calibration is finished. 

Valve Setup 

The PGA 3510 uses four flow control valves for nitriding gas analysis. These valves are enabled and set up 

in the Valve Setup window. 

 

Summary of Contents for PGA 3510











































Reviews:

No comments