background image

1

Important Safety Instructions

Before beginning any fitness program, you should obtain a complete
physical examination from your physician. When using exercise equipment,
basic precautions should always be taken, including the following:

* Read all instructions before using the Bicep/Tricep Combo. These

instructions are written to ensure your safety and to protect the unit.

* Do not allow children on or near the equipment.
* Use the equipment only for its intended purpose as described in this guide.

Do not use accessory attachments that are not recommended by the
manufacturer: such attachments might cause injuries.

* Wear proper exercise clothing and shoes for your workout----no loose

clothing.

* Be careful when getting on or off the equipment.
* Do not overexert yourself or work to exhaustion.
* If you feel any pain or abnormal symptoms, stop your workout immediately

and consult your physician.

* Never operate the unit when it has been dropped or damaged.
* Never drop or insert anything into any opening in the equipment.
* Always check the unit and its cables before each use. Make sure that all

fasteners and cables are secure and in good working condition.

* Frayed or worn cables can be dangerous and may cause injury.

Periodically check these cables for any indication of wear.

* Keep hands, limbs, loose clothing and long hair well out of the way of

moving parts.

* Do not attempt to lift more weight than you can control safely.
* Do not use the equipment outdoors.

* Read each step in the assembly instructions and follow the steps in

sequence. Do not skip ahead. If you skip ahead, you may learn later that
you have to disassemble

and that you may have damaged

the equipment.

* Assemble and operate the equipment on a solid, level surface. Locate the

unit a few feet from walls or furniture to provide easy access. The
Bicep/Tricep Combo is designed for your enjoyment. By following these
precautions and using common sense, you will have many safe and
pleasurable hours of healthful exercise with the equipment.

Personal Safety During Assembly

comportments

Summary of Contents for SG8023MT
















Reviews: