background image

13

5.  INTENDED PRODUCTS FOR CE MARKING

The models listed under “

6. Speci  cations

” come with CE Marking.

As for all other models, please contact our of  ce.

Be sure to meet condition 1). Furthermore, either condition 2) or 3) should also be met.

1) Cable length between the main power supply and the controller should be less than 10m.
2) When the power is supplied from 

S-LINK V

 controller to I/O devices at a cable distance of more 

than 10m, add a surge absorber between 24V and 0V at a cable distance of less than 10m.

  Recommended surge absorber: ERZ05D390 (Manufactured by Matsushita Electronic Compo-

nents Co., Ltd.)

3) Use a local power supply at a cable distance of less than 10m from each I/O device.

[Conditions in use for CE conformity]

Note:  Do not connect a surge absorber between D and G.

Conditions

bit 3: “Error interruption” sets whether an interruption occurs or not when an error occurs.

 

When bit 3 is “1” an interruption occurs, and when bit 3 is “0” the interruption does not oc-

cur.

 

In case the error interruption is set to effective, the interruption occurs with OR operation 

applied to all error occurrences.

 

For contents of error, check by “

5) HML0 + 48: Error No. / Error state

.“

Note: In case bit 2 (Input change interruption) and bit 3 (Error interruption) are both “1,” bit 3 (Error interrup-

tion) has priority. Input change interruption does not occur.

Summary of Contents for SL-VISA

















Reviews: