Adjust
zero-point
Commence
measurement
on completion
of setting
Enter
Set Value 1 (P1)
Set Value 2 (P2)
Set Value 3 (P3)
Set [Display],
[Output mode],
and [Unit]
DP2-20
–101.3kPa
OUT2
OUT1
MODE
0-ADJ
06H0143
3rd digit
2nd digit
Change with key.
1st digit
06H0145
Unit
Output mode
Display
: kPa or
MPa
: kgf/cm
2
: bar
: psi
: Hysteresis
mode
: Window
comparator
mode
: Digital
display
: Analog
bar
display
: Dual output
mode
: Automatic
sensitivity
setting mode
: mmHg
: inHg
Positive
pressure type
Vacuum
pressure type
11
SETTING
䢇
If key-protect has been set, make sure to release key-
protect before operating the keys. (Please refer to KEY-
PROTECT FUNCTION for the procedure.)
䢇
The conditions which are set are stored in an EEPROM.
Kindly note that the EEPROM has a life span and its
guaranteed life is 100,000 write operation cycles.
15
1
Zero-point
adjustment
2
Initial
setting
3
Pressure
value setting
Measurement
1
Zero-point adjustment
䢇
The displayed pressure when the pressure port is left open is
adjusted to zero.
Set to sensing mode
DP2-20
–101.3kPa
OUT2
OUT1
MODE
0-ADJ
•
The sensor will automatically enter the
sensing mode when power is supplied.
•
The figure on the left shows the display
when the pressure unit and display are set
to ‘kPa
’
and ‘digital display
’
, respectively.
2
Initial setting
䢇
Pressure [Unit], [Display] and [Output mode] of the
comparative outputs are set.
Set to initial setting mode
DP2-20
–101.3kPa
OUT2
OUT1
MODE
0-ADJ
•
In the sensing mode, press key while
pressing key.
•
Initial setting is displayed.
•
If sensor is being used for the first time,
is displayed.
Perform zero-point adjustment
DP2-20
–101.3kPa
OUT2
OUT1
MODE
0-ADJ
•
Let the pressure port be at atmospheric
pressure (i.e., no applied pressure condi-
tion), and press, simultaneously, the incre-
ment and decrement keys continuously.
•
is displayed and, when the finger is
released, zero-point adjustment is
completed and the sensor returns to the
sensing mode.
DP2-20
–101.3kPa
OUT2
OUT1
MODE
0-ADJ
•
If pressure has been applied during zero-
point adjustment, is displayed when
the keys are pressed. Bring the applied
pressure to atmospheric pressure (i.e., no
applied pressure condition) and carry out
the zero-point adjustment once again.
Set initial conditions
•
The settable digit blinks.
•
The settable digit changes when key
is pressed.
DP2-20
–101.3kPa
OUT2
OUT1
MODE
0-ADJ
•
Change the setting of each digit as desired.
•
The setting is changed when key is
pressed.
Set to sensing mode
DP2-20
–101.3kPa
OUT2
OUT1
MODE
0-ADJ
•
Press key.
•
The sensor returns to sensing mode after
the initial conditions have been set.
•
Since the initial conditions which have
been set are stored in an EEPROM, they
are not erased even if the power supply is
switched off.
•
The figure on the left shows the display
when the unit and display are set to ‘kPa’
and ‘digital display’, respectively.
MODE
MODE
Setting procedure
For the case when output mode is set to either the hysteresis mode
( ), window comparator mode ( ) or dual output mode ( ).
For the case when the output mode is set to automatic
sensitivity setting mode ( )
3
Setting of pressure values
䢇
[Set Value 1 (P1)] and [Set Value 2 (P2)] of the comparative
outputs are set.
䢇
Comparative outputs’ [Set Value 1 (P1)], [Set Value 2 (P2)]
and [Set Value 3 (P3)] are set.
Set to sensing mode
DP2-20
–101.3kPa
OUT2
OUT1
MODE
0-ADJ
•
Press key.
•
The sensor returns to sensing mode after
Set Value 1 (P1) and Set Value 2 (P2)
have been set.
•
Since the values which have been set are
stored in an EEPROM, they are not
erased even if the power supply is
switched off.
MODE
•
The setting of Set Value 2 (P2) with respect to Set Value 1
(P1) can only be towards the high pressure side in case of
the positive pressure type sensor and only towards the high
vacuum side in case of the vacuum pressure type sensor.
•
Set Value 1 (P1) and Set Value 2 (P2) can be made common
for all the output modes. However, when a changeover is
made to the automatic sensitivity setting mode, since Set
Value 3 (P3) has not been set, make sure to carry out the
pressure value settings for the automatic sensitivity mode.
•
The setting of Set Value 2 (P2) with respect to Set Value 1
(P1) can only be towards the high pressure side in case of
the positive pressure type sensor and only towards the high
vacuum side in case of the vacuum pressure type sensor.
•
Set Value 3 (P3) is automatically set to the mid-value of Set
Value 1 (P1) and Set Value 2 (P2). However, if Set Value 1
(P1) is set to a value on the vacuum pressure side for a
positive pressure type sensor or to the positive pressure side
for a vacuum pressure type sensor, Set Value 3 (P3) is
automatically set to the mid-value of ‘zero’(atmospheric
pressure) and Set Value 2 (P2). Further, if both, Set Value 1
(P1) and Set Value 2 (P2) are set to a value on the vacuum
pressure side for a positive pressure type sensor or to the
positive pressure side for a vacuum pressure type sensor, Set
Value 3 (P3) is automatically set to ‘zero’(atmospheric
pressure).
•
The automatically set Set Value 3 (P3) can be changed manually.
•
Since display of error messages is not possible during
pressure value setting in the automatic sensitivity setting
mode, make sure that the sensor is used within the rated
pressure range.
Set to Set Value 1 (P1) set mode
DP2-20
–101.3kPa
OUT2
OUT1
MODE
0-ADJ
DP2-20
–101.3kPa
OUT2
OUT1
MODE
0-ADJ
Displayed
alternately
•
In the sensing mode, press key.
•
and Set Value 1 (P1) which is being
set are displayed alternately.
•
The figure on the left shows the display of
a vacuum pressure type sensor when the
pressure unit has been set to ‘kPa’.
Enter Set Value 1 (P1)
DP2-20
–101.3kPa
OUT2
OUT1
MODE
0-ADJ
DP2-20
–101.3kPa
OUT2
OUT1
MODE
0-ADJ
Displayed
alternately
•
Enter using key and key.
•
In case of the positive pressure type
sensor, if key is pressed once the set
value changes towards the high pressure
side by 1 digit and if key is pressed
once the set value changes towards the
low pressure side by 1 digit.
In case of the vacuum pressure type
sensor, if key is pressed once the set
value changes towards the high vacuum
side by 1 digit and if key is pressed
once the set value changes towards the
low vacuum side by 1 digit.
•
If key or key is pressed con-
tinuously, the set value changes quickly.
•
If the set pressure range is exceeded,
either (upper limit exceeded) or
(lower limit exceeded) is displayed.
Set to Set Value 2 (P2) set mode
DP2-20
–101.3kPa
OUT2
OUT1
MODE
0-ADJ
DP2-20
–101.3kPa
OUT2
OUT1
MODE
0-ADJ
Displayed
alternately
•
In the Set Value 1 (P1) set mode, press
key.
•
and Set Value 2 (P2) which is
being set are displayed alternately.
MODE
MODE
Enter Set Value 2 (P2)
DP2-20
–101.3kPa
OUT2
OUT1
MODE
0-ADJ
DP2-20
–101.3kPa
OUT2
OUT1
MODE
0-ADJ
Displayed
alternately
•
Using key and key, enter in a
manner similar to that for entering Set
Value 1 (P1).
•
If the set pressure range is exceeded,
either (upper limit exceeded) or
(lower limit exceeded) is displayed.
•
If the output mode has been set to the window comparator
mode ( ) in the initial setting mode, Set Value 1 (P1) and
Set Value 2 (P2) should be set with a difference of 3 digits
or more. However, when unit is set to ‘psi’, the difference
should be 6 digits or more.
Set to Set Value 1 (P1) set mode
DP2-20
–101.3kPa
OUT2
OUT1
MODE
0-ADJ
DP2-20
–101.3kPa
OUT2
OUT1
MODE
0-ADJ
Displayed
alternately
•
In the sensing mode, press key.
•
and Set Value 1 (P1) which is being
set are displayed alternately.
•
The figure on the left shows the display of
a vacuum pressure type sensor when the
pressure unit has been set to ‘kPa’.
Enter Set Value 1 (P1)
DP2-20
–101.3kPa
OUT2
OUT1
MODE
0-ADJ
DP2-20
–101.3kPa
OUT2
OUT1
MODE
0-ADJ
Displayed
alternately
•
Within the required permissible pressure
range, having created a pressure state
which is nearest to the atmospheric
pressure, press key.
•
The pressure value at the time of pressing
key is entered as Set Value 1 (P1). Set
Value 1 (P1) and are displayed
alternately.
•
If the set pressure range is exceeded,
either (upper limit exceeded) or
(lower limit exceeded) are displayed
and Set Value 1 (P1) is set automatically
to the upper or lower limit of the set
pressure range.
•
The setting of Set Value 1 (P1) can be
repeated several times in the Set Value 1
(P1) set mode.
Set to Set Value 2 (P2) set mode
DP2-20
–101.3kPa
OUT2
OUT1
MODE
0-ADJ
DP2-20
–101.3kPa
OUT2
OUT1
MODE
0-ADJ
Displayed
alternately
•
In the Set Value 1 (P1) set mode, press
key.
•
and Set Value 2 (P2) which is being
set are displayed alternately.
MODE
MODE
Enter Set Value 2 (P2)
DP2-20
–101.3kPa
OUT2
OUT1
MODE
0-ADJ
DP2-20
–101.3kPa
OUT2
OUT1
MODE
0-ADJ
Displayed
alternately
•
Within the required permissible pressure
range, having created a pressure state
which is nearest to the high pressure end
(for a positive pressure type sensor) or
the high vacuum end (for a vacuum
pressure type sensor), press key.
•
The pressure value at the time of pressing
key is entered as Set Value 2 (P2). Set
Value 2 (P2) and are displayed
alternately.
•
If the set pressure range is exceeded,
either (upper limit exceeded) or
(lower limit exceeded) are displayed
and Set Value 2 (P2) is set automatically
to the upper or lower limit of the set
pressure range.
•
The setting of Set Value 2 (P2) can be
repeated several times in the Set Value 2
(P2) set mode.
