manualshive.com logo in svg

Suntex PC-300A Series, Operation Manual, Page: 21 / 36

Share
Download
Suntex PC-300A Series Operation Manual Download Page 21

3.6 Wiring description of PH-300T 

      2-wire distribution system: 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2-wire distribution system 

pH/ORP sensor & 

temp. probe 

PH-300T 

terminals 

 

PH-300T 

terminals 

Coaxial 4-core wire 

(7202-F94009-BK) 

Terminals on 

transmitter 

Coaxial inner 

GLASS 

 

S+ 

Coaxial inner 

GLASS 

Coaxial shield 

REF. 

 

S- 

Coaxial shield 

REF 

Green wire 

PT-1000 

 

V- 

Green wire 

-12V 

Red wire 

 

 

V+ 

Red wire 

+12V 

Note:   

1. It is necessary to make REF and SG terminals short-circuited for PH-300T if 2-wire 

 

distribution system is applied (with a built-in jumper between them). 

 

2. The black wire would be forbidden if 8-26-8 is used as 2-wire distribution. 

 

3. It is necessary to apply our coaxial 4-core wire: 7202-F94009-BK.

 

(Short-circuited) 

紅

 

-

 

Green   

Green   

Red     

Red     

Shield       

Shield       

Transparent         

Transparent         

Black (NC)         

Transparent         

Red           

Gr         

Shield           

pH/ORP 

sensor 

Temperature 

probe 

18

Summary of Contents for PC-300A Series





































Reviews:

No comments