manualshive.com logo in svg

SunStar KM-380BL, User Manual

Share
Download
SunStar KM-380BL User Manual Download Page 9

9

Caution

▶

Do not plug in only before oil supply is finished.  
If the operator mistakenly steps on the pedal with the plug in, the machine will start
automatically and can cause severe injuries.

▶

When handling lubricants, wear protective glasses or gloves to avoid contact with your eyes or
skin.  Inflammation may be caused otherwise.  Never drink lubricants since they can cause
vomiting or diarrhea.  Keep out of the reach of children.

▶

Operate the machine only after adding oil when the machine is being used for the first time or
has been left unused for a long time.

[Figure 1]

1) Confirming oil supply

A. Confirming oil tank

KM-380BL/390BL

In case of oil tank installed in the upper part of arm, supply
oil to the level of the marked line

after opening the cover

. (Refer to Figure 1)

2) Lubricating each friction part

Be sure to supply oil into the oil holes marked red (arrow marks) and the oil holes in the friction parts before operating the machine.

[Figure 2]

[Figure 3]

Summary of Contents for KM-380BL

























Reviews:

No comments

Brands by name

Popular brands

Load more brands