manualshive.com logo in svg

SunStar KM-380BL, User Manual

Share
Download
SunStar KM-380BL User Manual Download Page 13

13

5) Routing upper thread

KM-380BL/390BL

Place the thread take-up lever to the highest position and hang
the upper thread like in Figure 14.

[Figure 14]

6) Adjusting upper thread tension

KM-380BL/390BL

A. Adjusting the upper thread tension

- Like in Figure 15, turning the tension adjustment nut

of the thread tension control assembly clockwise makes the upper

thread tension stronger and counterclockwise makes it weaker. 

B. Adjusting the thread take up 

a. Adjusting the thread take up stroke

- As in Figure 15, loosen the stopper fastening screw , and turn the thread take up spring stopper

counter clockwise to

make the operational scope of the thread take up spring 

bigger, and clockwise to make it smaller.

Caution

▶

Turn off the power switch when routing the upper thread.  

If the operator mistakenly presses down on the pedal while switched on, the machine will start

automatically and can cause physical injuries.

▶

When using the clutch motor, be aware that the motor will continue to rotate for a while even

after the power is switched off due to inertia.  

Start to work on the sewing machine only after the motor has come to a complete stop.

[Figure 15]

good swing

when the upper thread tension is strong

when the upper thread tension is weak

Summary of Contents for KM-380BL

























Reviews:

No comments

Brands by name

Popular brands

Load more brands