background image

930302 Rev. E

V I .

W a r n i n g s :   F a l l s   &   T i p - O v e r s

13

C. WHEELIES

Doing a “wheelie” means: balancing on the rear wheels of your chair, while the front
casters are in the air. It is dangerous to do a “wheelie” as a fall or tip-over may occur.
However, if you do it safely, a “wheelie” can help you overcome curbs and obstacles. 

1. Consult your doctor, nurse or therapist to find out if you are a good candidate to

learn to do a “wheelie.”

2. Do not attempt a “wheelie” UNLESS you are a skilled rider of this chair, 

or you have help.

NOTE– 

See steps to learn to do a “wheelie.”

If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of con-
trol may occur and cause severe injury to the rider or others.

D. OBSTACLES

Obstacles and road hazards (such as potholes and broken pavement) can damage your
chair and may cause a fall, tip-over or loss of control. 

To avoid these risks:
1. Keep a lookout for danger – scan the area well ahead of your chair as you ride.
2. Make sure the floor areas where you live and work are level and free of obstacles.
3. Remove or cover threshold strips between rooms.
4. Install a ramp at entry or exit doors. Make sure there is not a drop off at the

bottom of the ramp. 

5. To Help Correct Your Center Of Balance:

a. Lean your upper body FORWARD slightly as you go UP over an obstacle. 
b. Press your upper body BACKWARD as you go DOWN from a higher to a lower

level.

6. If your chair has anti-tip tubes, lock them in place before you go UP over an

obstacle.

7. Keep both of your hands on the handrims as you go over an obstacle.
8. Never push or pull on an object (such as furniture or a doorjamb) to propel 

your chair.

If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of con-
trol may occur and cause severe injury to the rider or others.

V I .

W a r n i n g s :   F a l l s   &   T i p - O v e r s

930302 Rev. E

12

A. CENTER OF BALANCE

The point where this chair will tip forward, back or to the side depends on its center
of balance and stability. How your chair is set up, the options you select and the
changes you make may affect the risk of a fall or tip-over.

1. The Most Important Adjustment Is: 

The position of the rear wheels. The more you move the rear wheels forward, 
the more likely your chair will tip over backward.

2. The Center Of Balance Is Also Affected By:

a. A change in the set-up of your chair, including:

• The distance between the rear wheels.
• The amount of rear wheel camber.
• The seat height and seat angle.
• Backrest angle.

b. A change in your body position, posture or weight distribution.
c. Riding your chair on a ramp or slope.
d. The use of a back pack or other options and the amount of added weight.

3. To Reduce The Risk Of An Accident:

a. Consult your doctor, nurse or therapist to find out what axle and caster 

position is best for you.

b. Consult your authorized supplier BEFORE you modify or adjust this chair. 

Be aware that you may need to make other changes to correct the center 
of balance.

c. Have someone help you until you know the balance points of your chair and

how to avoid a tip-over.

d. Use anti-tip tubes.

If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of con-
trol may occur and cause severe injury to the rider or others.

B. DRESSING OR CHANGING CLOTHES

Your weight may shift if you dress or change clothes while seated in this chair. 

To reduce the risk of a fall or tip-over:
1. Rotate the front casters until they are as far forward as possible. 

This makes the chair more stable. 

2. Lock anti-tip tubes in place. (If your chair does not have anti-tip tubes, back it

up against a wall and lock both rear wheels).

If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of con-
trol may occur and cause severe injury to the rider or others.

Summary of Contents for Quickie 2 Series


























Reviews: