background image

930302 Rev. E

V I I I .

W a r n i n g s :   C o m p o n e n t s   &   O p t i o n s

23

G. POSITIONING BELTS (OPTIONAL)

Use positioning belts ONLY to help support the rider’s posture. Improper use of these
belts may cause severe injury to or death of the rider.

1. Make sure the rider does not slide down in the wheelchair seat. If this occurs,

the rider may suffer chest compression or suffocate due to pressure from the
belts.

2. The belts must be snug, but must not be so tight that they interfere with

breathing. You should be able to slide your open hand, flat, between the belt
and the rider.

3. A pelvic wedge or a similar device can help keep the rider from sliding down in

the seat. Consult with the rider’s doctor, nurse or therapist to find out if the
rider needs such a device.

4. Use positioning belts only with a rider who can cooperate. Make sure the rider

can easily remove the belts in an emergency.

5. NEVER Use Positioning Belts:

a. As a patient restraint. A restraint requires a doctor’s order.
b. On a rider who is comatose or agitated.
c. As a motor vehicle restraint. In an accident or sudden stop the rider may be

thrown from the chair. Wheelchair seat belts will not prevent this, and fur-
ther injury may result from the belts or straps.

If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of con-
trol may occur and cause severe injury to the rider or others.

H. POWER DRIVE

Do not install a power drive on any Quickie wheelchair. If you do:

1. It will affect the center of balance of your chair and may cause a fall or tip-over.
2. It will alter the frame and void the warranty.

If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of con-
trol may occur and cause severe injury to the rider or others. 

I. PUSH HANDLES (OPTIONAL)

When you have an attendant, make sure that this chair has push handles. 

1. Push handles provide secure points for an attendant to hold the rear of this

chair, to prevent a fall or tip-over. Make sure to use push handles when you have
an attendant.

2. Check to make sure push handle grips will not rotate or slip off.

If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of con-
trol may occur and cause severe injury to the rider or others. 

V I I I .

W a r n i n g s :   C o m p o n e n t s   &   O p t i o n s

930302 Rev. E

22

D. FASTENERS

Many of the screws, bolts and nuts on this chair are special high-strength fasteners. 
Use of improper fasteners may cause your chair to fail. 

1. ONLY use fasteners provided by an authorized supplier (or ones of the same type

and strength, as indicated by the markings on the heads).

2. Over- or under-tightened fasteners may fail or cause damage to chair parts. 
3. If bolts or screws become loose, tighten them as soon as you can.

If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of con-
trol may occur and cause severe injury to the rider or others.

E. FOOTRESTS

1. At the lowest point, footrests should be AT LEAST 2 1/2 INCHES off the ground.

If set too LOW, they may “hang up” on obstacles you can expect to find in nor-
mal use. This may cause the chair to stop suddenly and tip forward.

2. To Avoid A Trip Or Fall When You Transfer:

a. Make sure your feet do not “hang up” or get caught in the space between

the footrests.

b. Avoid putting weight on the footrests, as the chair may tip forward.

3. NEVER lift this chair by the footrests. Footrests detach and will not bear the

weight of this chair. Lift this chair only by non-detachable parts of the main
frame.

If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of con-
trol may occur and cause severe injury to the rider or others.

F. PNEUMATIC TIRES

Proper inflation extends the life of your tires and makes your chair easier to use.

1. Do not use this chair if any of the tires are under- or over-inflated. Check weekly

for proper inflation level, as listed on the tire sidewall.

2. Low pressure in a rear tire may cause the wheel lock on that side to slip and

allow the wheel to turn when you do not expect it. 

3. Low pressure in any of the tires may cause the chair to veer to one side and

result in a loss of control.

4. Over-inflated tires may burst.

If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of con-
trol may occur and cause severe injury to the rider or others.

Summary of Contents for Quickie 2 Series


























Reviews: