Sunrise Medical Breezy Relax, Directions For Use Manual

Page: 6 / 16

Breezy Relax/Quickie Relax
17
EE
NN
GG
LL
IISS
HH
0305/3/ST-000690xxx.EMS
Standard flip-up footrest (7.24.1)
To flip up:
Take the load off the footrest and
release the hand wheel (1). Pull the
footrest upwards and set the desi-
re height. Secure at the desired
height by tightening the hand
wheel.
To lower:
Take the load off the footrest by lif-
ting the lower leg and release the
interlock with the hand wheel (1). In this way you can swing
the footrest downwards. As soon as you have reached the
desired position, secure the interlock with the hand wheel.
You can set the lower leg length by releasing the screws (2),
this is infinitely adjustable.
CAUTION! Risk of injury!
When moving the footrest up or down, do not put your
fingers in the adjusting mechanism between the moving
parts of the footrest.
CAUTION!
The footrests are not designed to be used to lift or carry
the wheelchairs with an occupant.
Angle-adjustable footboard
(7.22)
The footboard can be flipped up
to make it easier to transfer
to/from the chair.
It can be adjusted to alter the
angle to the ground. Loosen screw
(1) and set the desired angle. Then
tighten the screw.
By loosening the screw (1) the
footboard can be adjusted both
forwards and backwards. Make
sure that after any adjustment
work, all screws are tightened cor-
rectly (see the page on torque).
Ensure that you maintain the mini-
mum gap to the floor (2.5 cm).
CAUTION!
While making the adjustment,
there must be no load on the
footboard!
Options – Angle-adjustable footboard
Headrest (7.35)
The headrest can be raised,
moved sideward and moved hori-
zontally both forwards and back-
wards.
Height adjustment: Pull the release
knob (1) and set the desired
height. Make sure that the release
knob is always correctly engaged.
Horizontal adjustment: Open the
release lever (2), set the desired
position and pull the release lever
firmly again.
Side adjustment: After loosening the screws (3) the
headrest can be pushed sideways. Tighten screws
again (see the page on torque).
Options - Headrest
1
2
3
1
2
1
1
Calf pads can be width and depth adjusted. To
do this, release the screws (1) and
push the calf pad into the relevant
position. After making the adjust-
ment, all screws must be correctly
tightened. By pushing the calf pad
on the footrest tube, you can set the
height.
Seat height adjustment (7.51.1.1)
Seat height can be adjusted by
changing the position of the
castors and rear wheels (see table
1) as well as by using the seating
unit. To make the adjustment the 4
screws (4) must be loosened and
the seating unit must be screwed
into the new position (A, B). After
making the adjustment, all screws
must be correctly tightened (see the page on torque).
Abduction wedge
By loosening the screw (1) the
abduction wedge can be adjusted
height-wise and by loosening the
screws (2, 3) it can be adjusted
depth-wise or removed.
Options - Seat height adjustment
3
1
2
Seat Castor Castor Rear wheel Rear Seat
heights fixing fixing wheel unit
41 cm 1 6" 1 20" A
43 cm 1 6" 1 20" B
45 cm 1 8" 1 24" A
45 cm 2 8" 2 16" A
47 cm 1 8" 1 24" B
47 cm 1 8" 4 16" B
47,5 cm 2 8" 2 24" A
49,5 cm 2 8" 2 24" B
50 cm 3 8" 3 24" A
52 cm 3 8" 3 24" B
A
4 1 2 3
B