Choose the objects you would like to control:
•
Short press Group number button 1, all associated devices of Association Group 2 are the objects which the
command will be sent to.
•
Short press Group number button 2, all associated devices of Association Group 3 are the objects which the
command will be sent to.
•
Short press Group number button 3, all associated devices of Association Group 4 are the objects which the
command will be sent to.
•
Short press Group number button 4, all associated devices of Association Group 5 are the objects which the
command will be sent to.
Control the objects you would like to control:
•
Double click Group number button 1-4, activation of scenes in Gateways using Command Class Central
Scene.
•
Short press Scene button S1/S2/S3/S4, direct control of associated devices using Scene Activation Set,
Scene ID = 0x10 / 0x20 / 0x30 / 0x40 to the last used Group 2, 3, 4 or 5.
•
Press and hold down Scene button S1/S2/S3/S4, direct control of associated devices using Scene Conf Set,
Scene ID = 0x10 / 0x20 / 0x30 / 0x40 to the last used Group 2, 3, 4 or 5.
•
Short press “ALL ON/OFF” button, direct control of associated devices using Basic Set On/Off commands.
•
Short touch or slide touch the “Color Wheel”, direct control of associated devices using Color Switch Set
commands.
•
Press and hold down brightness down and brightness up buttons, direct control of associated devices using
Multilevel Switch Start Level Change Set commands.
Node Information Frame
The Node Information Frame is the business card of a Z-Wave device. It contains information about the device
type and the technical capabilities. The inclusion and exclusion of the device is confirmed by sending out a
Node Information Frame. Beside this it may be needed for certain network operations to send out a Node
Information Frame.
How to send out Node Information Frame:
Manufacturer Specific
Parameter
Manufacturer ID
Product Type ID
Product ID
Value (hex)
0x0330
0x0300
0xa103
SUPPORTED COMMAND CLASS
Node Info
V2
V1
V1
V2
V1
V4
V3
COMMAND_CLASS_ZWAVEPLUS_INFO
COMMAND_CLASS_SECURITY
COMMAND_CLASS_SECURITY_2
COMMAND_CLASS_TRANSPORT_SERVICE
COMMAND_CLASS_SUPERVISION
COMMAND_CLASS_SWITCH_MULTILEVEL
COMMAND_CLASS_SWITCH_COLOR
Support S2
To remove all associated devices in an association group on the wall controller directly:
1. Press and hold down “ALL ON/OFF” button on the wall controller for over 3 seconds, LED indicator turns on.
2. Click any Group number button on the wall controller 5 times continuously within 25 seconds to remove all
associated devices of this group, LED indicator blinks 8 times to indicate that the associated devices are
removed successfully.
4 Groups
Decrease whole brightness
Increase whole brightness
Save and recall 4 scenes
ALL ON/OFF button, broadcast to turn on/off all
Color Wheel for adjusting relative brightness
between PWM1 and PWM2
50% PWM1 +50% PWM2
100% PWM1 + 0% PWM2
0% PWM1 + 100% PWM2
IP Rating
Frequency
SDK
Explorer Frame Support
Device Type
Generic Device Class
Specific Device Class
Routing
FLiRS
IP 20
868.42 MHz (EU)
Up to 100 m outside, on average up to
40 m inside buildings
6.71.01
Yes
Wall Controller
Wall Controller
Basic Wall Controller
Yes
No
Wireless Range
Z-Wave Plus Info
Parameter
Z-Wave Plus Version
Role Type
Node Type
Installer Icon Type
User Icon Type
Value
1
Slave Always On
ZWAVEPLUS
0x1600 (ICON_TYPE_GENERIC_WALL_CONTROLLER)
0x1600 (ICON_TYPE_GENERIC_WALL_CONTROLLER)
Set the wall controller into inclusion/exclusion mode: press and hold down “ALL ON/OFF” button for over 3
seconds, or short press the “inclusion/exclusion” button, LED indicator turns on to indicate the wall controller
has already sent out Node Information Frame, the user can repeat the operation to set the wall controller to quit
“inclusion/exclusion mode”.
Technical Data
