background image

 

 

IMPORTANT SAFETY INSTRUCTIONS 

 

When using an electrical appliance, basic precautions should always be followed, including 
the following: 
 
Read all instructions before using this treadmill. 
 

DANGER

 

– To reduce the risk of electrical shock: 

1. Always unplug this appliance from the electrical outlet immediately after using and before 
cleaning. 

 

WARNING

 

– To reduce the risk of burns, fire, electric shock, or injury to persons: 

1.  The treadmill should never be left unattended when plugged in. Unplug from outlet when 

not in use and before putting on or taking off parts. 

2.  Use  this  treadmill  only  for  its  intended  use  as  described  in  this  manual.  Do  not  use 

attachments not recommended by the manufacturer. 

3.  Never operate this treadmill if it has a damaged cord or plug, is not working properly, has 

been dropped or damaged.   

4.  Keep the cord away from heated surfaces. 
5.  Never operate the treadmill with the air openings blocked. Keep the air openings free of 

lint, hair, and the like. 

6.  Never drop or insert any object into any opening. 
7.  Do not use outdoors. 
8.  Do not operate where aerosol (spray) products are being used or where oxygen is being 

administered. 

9.  To disconnect, turn the treadmill off, then remove plug from outlet. 
10. Connect this treadmill to a properly grounded outlet only. See grounding instructions. 
 
 

CAUTION

:

 Risk of Injury to Persons: 

To  avoid  injury,  use  extreme  caution  when  stepping  onto  or  off  of  a  moving  belt.  Read 
Instruction Manual Before Using. 
 
 

SAVE THESE INSTRUCTIONS 

 

 

WARNING:

 This product can expose you to one or more chemicals known to the 

State  of  California  to  cause  cancer  and  birth  defects  or  reproductive  harm.  For 
more information go to www.P65Warnings.ca.gov. 

 

 

 
 
 

Summary of Contents for SF-T7643
























Reviews: