Sunjoy L-DN1856SST-E-T Assembly Instruction Manual Download Page 14

14 of 15 

 
NOTE:

 

While in use, the burner flame should be mainly blue in appearance with a small amount of yellow. 

The flame can be identified by the following figure. 

 

 

 

 

 

 

 

 

 

 

 

 

 

Warning: Lighting the Fire Pit improperly could lead to an unsafe condition. 

7.  Press  in  and  turn  the  control  valve  knob  clockwise  to  OFF  to  shut  down  fireplace.  Close  the  gas 
cylinder valve when the fireplace is not in use. 
(

CAUTION:

 Do not kink flexible gas hose. If it is kinked, a gas leak could occur.) 

 

STORAGE AND MAINTENANCE:   

To  obtain  the  best  performance  from  your  fireplace,  you  must  perform  the  following  storage  and 

 

  Allow at least 35 minutes for the fireplace to cool down after use, before disconnecting and removing 

 

  Store the gas cylinder in a dry, well-ventilated and sheltered area protected from inclement weather 

and dust, out of the reach of children, and not in a bui

 

 

 

  Keep the fireplace area clear and free from combustible materials, gasoline and other flammable 

 

 

Installation and repair should be done by a qualified service person. The fireplace should be 

inspected before use and at least annually by a qualified service person. More frequent cleaning 
may be required as necessary. It is imperative that the control compartment, burner, and 
circulating air passageways of the fireplace be kept clean. 

  If you disassemble the burner when cleaning the fireplace, please 

reassemble it according to the picture on the right to make sure the burner 
induction tunnel is on and exactly cover the orifice base. 

It is imperative that 

the control compartment, burner, and circulating air passageways of the 
fireplace be kept clean. 

 

  Permanent installation and repair should be done by a qualified service 

person. The fireplace should be inspected annually by a qualified service 
person.

 

 

 
 
 
 

Summary of Contents for L-DN1856SST-E-T
















Reviews: