background image

2

•  Risk of explosion – Do not spray flammable liquids.
•  Disconnect the tool – Disconnect from the electrical power 

supply before performing any maintenance task.

•  Keep children away – This high-pressure electric  

power washer must not be used by children or  

untrained personnel.

•  To ensure appliance safety, use only original  

replacement parts from the manufacturer or those  

approved by the manufacturer.

m

WARNING! 

Water that has flowed through backflow 

preventers is considered to be non-potable.

m

WARNING! 

During cleaning, maintenance or when 

replacing parts, the machine must be disconnected from its 

power source by removing the plug from the socket outlet. 

m

WARNING! 

High-pressure hoses, fittings, and 

couplings are important for the safe operation of the  

appliance. Use only hoses, fittings, and couplings 

recommended by the manufacturer. 

•  Check for damaged parts – Do not use the appliance if 

the supply cord or other important parts of the appliance 

are damaged (e.g. safety devices, high-pressure hose, 

trigger gun).

•  This high-pressure electric power washer must not be used 

at temperatures below 32ºF (0°C).

m

WARNING! 

Power cords on drums should always be 

completely unwound to prevent the cord from overheating.

•  Power cord connections should be kept dry and off  

the ground.

•  If the power cord is damaged, do not use the appliance. 

Contact your authorized Snow Joe

®

 + Sun Joe

®

 dealer or 

call the Snow Joe

®

 + Sun Joe

®

 customer service center at 

1-866-SNOWJOE (1-866-766-9563).

•  Keep the machine on a stable, flat surface during operation, 

handling, transportation, and storage. Sudden overturn of 

the machine can cause bodily injury.

•  In the event of an accident or breakdown, switch off the 

machine immediately. (If contact with detergent occurs, 

rinse with an abundance of clean water.)

Electrical Safety

ATTENTION: 

If there are problems with the electrical mains, 

short voltage drops may appear when starting the equipment. 

This can, in turn, influence other equipment (e.g. cause a 

lamp to blink). If the MAINS-IMPEDANCE Zmax < 0.335 OHM, 

such disturbances are not expected (if you require assistance, 

contact your local supply authority for further information).

m

WARNING!

 

Electrical Shock Hazard – Before starting 

up your machine, please check it carefully for any defects.  

If you find any, do not start up your machine and contact  

your distributor.
The following should be observed when connecting the  

high-pressure electric power washer to the electric supply:

•  The electric supply connection should be performed by a 

qualified person.

•  The electric supply to this appliance should include either 

a residual current device that will interrupt the supply if the 

leakage current to the earth exceeds 30 mA for 30 ms or a 

device that will interrupt the earth circuit (GFCI).

IMPORTANT: 

Only use water without any impurities. 

If there is a risk of running sand into the inlet water (i.e. from 

your own well), an additional filter should be installed.

Safety Devices

The spray gun features a locking device. When the lock is 

activated, the spray gun cannot be operated.

1.  Thermal sensor – A thermal sensor protects the motor 

against overloading. If the thermal sensor is activated and 

the power is cut off, wait for a while until the motor is cool 

and restart the unit.

2.  Double insulation – In a double-insulated appliance, two 

systems of insulation are provided instead of grounding. 

No grounding means is provided on a double-insulated 

appliance, nor should a means for grounding be added 

to the appliance. Servicing a double-insulated appliance 

requires extreme care and knowledge of the system, and 

should be performed only by qualified service personnel at 

an authorized Snow Joe

®

 + Sun Joe

®

 dealer. Replacement 

parts for a double-insulated appliance must be identical 

to the parts they replace. A double-insulated appliance 

is marked with the words “Double Insulation” or “Double 

Insulated.” The symbol     (square within a square)  

may also be marked on the appliance.

3.  Ground fault circuit interrupter (GFCI) protection –  

This pressure washer is provided with a ground-fault 

circuit-interrupter (GFCI) built into the plug of the power-

supply cord. This device provides additional protection 

from the risk of electric shock. Should replacement of 

the plug or cord become necessary, use only identical 

replacement parts that include GFCI protection.

4.  It is not recommended to use an extension cord with this 

pressure washer. The unit comes standard with a 35 ft 

GFCI power cord. Using an extension cord may cause  

a drop in line voltage resulting in loss of power  

and overheating.

Summary of Contents for SPX2700-MAX-RM





















Reviews: