background image

Instruction of SR81 Split Pressurized Solar Hot Water System 

Page 55 of 59 

         

Note

: Manual heating is not a continuous heating process, it is triggered manually, and 

when the temperature reaches to the set point, the heating process is stopped. And manual 

heating function is stopped automatically.   

8.17 ECO Economic mode 

Function description

 

Under  the  ECO  economic  mode,  timing  heating  and  intelligent  heating  functions  are 

switched-off, only manual heating mode (M.H) can be used to trigger the electrical heater. 

 

Activate/deactivate this function: 

►Press  “ECO  Mode”  button,  sign            displays,  it 

indicates Eco mode is on.   

►Press “ECO Mode” button again, sign            closed, it indicates the ECO mode is off. 

8.18 DHW circuit pump triggered manually   

 

Note:

 Only when function of DHW circuit pump CIRC is activated, it is just possible to 

trigger the output R2 manually for running the DHW circuit pump. (Default pump runs for 3 

minutes) 

► Press “        “one time, to trigger the DHW circuit pump R2 

► Press “        “again, to cease the manual output. 

8.19 On/Off controller 

Under the on status   

►Press              button for 3 seconds; controller is switched-off, “OFF” shows on the screen.   

►Repress          button again, controller restarted.       
 

8.20 Holiday function 

The  holiday  function  is  used  for  operating  the  system  when  no  water  consumption  is 

expected,  e.  g. during  a  holiday  absence. This  function  cools  down  the  system  in  order  to 

reduce the thermal load. 

 

Activate/deactivate this function: 

►Press “Holiday” button for 3 seconds, “HDAY 05” 

displays on the screen 

Summary of Contents for SR81Q




























































Reviews: