background image

66037 REV. A 

Rev. 7/2/18

This is the safety alert symbol. It is used to alert you 
to potential personal injury hazards. Obey all safety 
messages that follow this symbol to avoid possible 
injury or death.

 

           

  

     

IMPORTANT: READ THESE INSTRUCTIONS BEFORE OPERATING

BEFORE USING THIS DEVICE, READ THIS MANUAL COMPLETELY AND THOROUGHLY, UNDERSTAND ITS OPERATING PROCEDURES, 
SAFETY WARNINGS AND MAINTENANCE REQUIREMENTS.

It is the responsibility of the owner to make sure all personnel read this manual prior to using the device. It is also the responsibility of the 
device owner to keep this manual intact and in a convenient location for all to see and read. If the manual or product labels are lost or not  
legible, contact Sunex for replacements. If the operator is not fluent in English, the product and safety instructions shall be read to and  
discussed with the operator in the operator's native language by the purchaser/owner or his designee, making sure that the operator  
comprehends its contents.

THE NATURE OF HAZARDOUS SITUATIONS

The use of portable automotive lifting devices is subject to certain hazards that cannot be prevented by mechanical means, but only by the 
exercise of intelligence, care, and common sense. It is therefore essential to have owners and personnel involved in the use and operation  
of the equipment who are careful, competent, trained, and qualified in the safe operation of the equipment and its proper use. Examples of 
hazards are dropping, tipping or slipping of loads caused primarily by improperly securing loads, overloading, off-centered loads, use on  
other than hard level surfaces, and using equipment for a purpose for which it was not designed.

METHODS TO AVOID HAZARDOUS SITUATIONS

 

•  Read, study, understand and follow all instructions before operating this device.

 

•  Inspect the jack before each use. Do not use jack if damaged, altered, modified, in poor condition, leaking hydraulic fluid, or 

 

  unstable due to loose or missing components. Make corrections before using.

 

•  Lift only on areas of the vehicle as specified by the vehicle manufacturer.

 

•  Wear eye protection that meets ANSI Z87.1 and OSHA standards (users and bystanders).

 

•  Do not use jack beyond its rated capacity. Do not shock Load.

 • 

This is a lifting device only. Immediately after lifting, support the vehicle with jack stands capable of sustaining  

 

 

  the load before working on the vehicle.

 

•  Use only on a hard level surface free from obstructions so the jack is free to reposition itself during lifting and lowering operations.

 

•  Center load on saddle. Be sure setup is stable before working on vehicle.

 

•  Do not move or dolly the vehicle while on the jack.

 

•  Do not use any materials that may serve as risers, spacers or extenders between the stock lifting saddle and the load.

 

•  Do not use any adapters that replace the stock lifting saddle unless approved or supplied by the jack manufacturer.

 

•  Do not use (or modify) this product for any other purpose than that for which it was designed without consulting the 

 

  manufacturer's authorized representative.

 

•  Always lower the jack slowly and carefully.

 

•  Handling the brass parts of this product will expose you to lead, a chemical known to the State of California to cause birth defects  

 

  and other reproductive harm. 

Wash hands after handling.

 

•  Failure to heed these warnings may result in serious or fatal personal injury and/or property damage.

  

WARNING:

 This product can expose you to chemicals including nickel which is known to the State of California to cause cancer and birth defects or other reproductive  

 

  harm.  For more information go to www.P65Warnings.ca.gov.

CONSEQUENCES OF NOT AVOIDING HAZARDOUS SITUATIONS

Failure to read this manual completely and thoroughly, failure to understand its OPERATING INSTRUCTIONS, SAFETY WARNINGS,
MAINTENANCE INSTRUCTIONS and comply with them, and failure to comply with the METHODS TO AVOID HAZARDOUS SITUATIONS
could cause accidents resulting in serious or fatal personal injury and/or property damage.

WARNING: Indicates a hazardous situation 
which, if not avoided, could result in death 
or serious injury.

WARNING

WARNING

WARNING

WARNING

WARNING INFORMATION

Summary of Contents for 66037





















Reviews: