SunEarth SolaRay 2 Installation, Operation And Maintenance Manual Download

Page: 40 / 50

P.36

SOLARAY 2 OG-300 SYSTEM LABELS

Labels containing the text below shall be attached to the appropriate valves on all SRCC

OG-300 certified systems.

FLUID IDENTIFICATION:

THE HEAT TRANSFER FLUID USED IN THIS SYSTEM IS INHIBITED

PROPYLENE GLYCOL. IT MUST BE HANDLED AND DISPOSED OF IN

ACCORDANCE WITH THE MANUFACTURERS RECOMMENDATIONS.

BE EXTREMELY CARFUL WHEN DRAINING THIS FLUID. IT MAY BE

DISCHARGED AT A VERY HIGH TEMPERATURE AND PRESSURE.

THE HEAT TRANFER FLUID USED IN THIS SYSTEM SHALL BE FDA

GENERALY RECOGNIZED AS SAFE (GRAS). NO OTHER FLUID SHALL BE

USED THAT WOULD CHANGE THE ORIGINAL CLASSIFICATION OF THIS

SYSTEM. UNAUTHORIZED ALTERATIONS TO THIS SYSTEM COULD RESULT

IN A HAZARDOUS HEALTH CONDITION.

PLEASE CONSULT SECTION 8 OF YOUR INSTALLATION

MANUAL FOR INSTRUCTION ON SHUTTING DOWN AND

DRAINING THE SYSTEM.

HEAT EXCHANGER

THE HEAT EXCHANGER USED IN THIS SYSTEM IS DOUBLE WALL VENTED

TO ATMOSPHERE. THE HEAT EXCHANGER IS INTEGRAL TO THE SOLAR

STORAGE TANK.

FREEZE LABEL:

A 60% CONCENTRATION OF PROPYLENE GLYCOL AND DISTILLED WATER

CAN PROTECT YOUR SOLARAY SYSTEM TO TEMPERATURES AS LOW AS

-60 F. LESSER CONCENTRATIONS OF DOWFROST HD AND DISTILLED

WATER WILL PROVIDE A LOWER LEVEL OF FREEZE PROTECTION.

PLEASE CONSULT SECTION 4.13.4 OF YOUR INSTALLATION

MANUAL FOR SPECIFIC FREEZE TOLERANCE INFORMATION.

VALVE NO. 23 - COLD WATER SUPPLY ISOLATION VALVE

THIS VALVE IS NORMALLY OPEN AND ALLOWS POTABLE WATER TO FILL

THE SOLAR STORAGE TANK. WHEN CLOSED THE SOLAR STORAGE TANK IS

ISOLATED FROM THE PRESSURIZED CITY COLD WATER SUPPLY LINE

PIPING.

VALVE NO. 5

–

TANK ISOLATION VALVE

VALVE 5 IS NORMALLY OPEN. WHEN CLOSED IN CONJUNCTION WITH

VALVE 14 THE SOLAR COLLECTOR LOOP PIPING IS ISOLATED FROM THE

SOLAR STORAGE TANK.

Appendix C

Summary of Contents for SolaRay 2



















































Search results

Summary of Contents for SolaRay 2

Reviews:

Related manuals for SolaRay 2

Brands by name

Popular brands

SunEarth SolaRay 2, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for SolaRay 2

Reviews:

Related manuals for SolaRay 2

Brands by name

Popular brands