background image

P.33

 

Circulator Pump 

The circulator pump shall be a wet rotor small circulator with a cast iron, stainless steel, 

brass or polymer body and a metal or polymer impeller.  The pump motor shall be 

induction or permanent magnet ECM driven.  The pump shall be rated for: maximum fluid 

temperatures of no less than 180

o

F and pressures of no less than 125 PSI.  The maximum 

rated amperage shall be no more than 1.5 Amps and the maximum rated power draw shall 

be no more than 135 Watts. 

 

Expansion Tank 

The expansion tanks shall be rated for non-potable propylene glycol based heat transfer 

fluids.  The maximum working temperature shall be no less than 180

o

F and the maximum 

working pressure shall be no less than 75 psi.  The expansion tank volume shall be not less 

than 2.0 gallons and the acceptance volume shall be not less than 1.0 gallon.  

 

Heat Transfer Fluid  

The heat transfer fluid shall be buffered propylene glycol based and shall have a maximum 

operating temperature of no less than 280

o

F.  If the HTF has a measurable flash point, at 

the concentrations used in the system, the HTF shall have a flash point of 400

o

F or higher. 

   

Thermostatic Mixing Valve 

The thermostatic mixing valve shall have a bronze, brass or stainless steel body with a 

rated maximum working temperature no less than 200

o

F and a rated maximum working 

pressure no less than 125psi.  The range of temperature set points shall be at least 18ºF 

(10ºC) and shall include a set point of 120ºF (50ºC).  The Thermostatic Mixing valve shall 

be third party listed and certified to one of the following ASSE standards: ASSE 1016; 

ASSE 1017; ASSE 1070.  

 

 

Ball Valves 

Ball valves shall be of bronze, brass or stainless steel construction.  Maximum working 

temperature shall be no less than 200

o

F and maximum working pressure shall be no less 

than 125 psi. 
 

Three-Way Valves (Optional) 

Three-Way valves shall be of bronze, brass or stainless steel construction.  Maximum 

working temperature shall be no less than 200

o

F and maximum working pressure shall be 

no less than 125 psi.   

 

Boiler Drains 

(A.K.A. Charge Valves; Fill Valves; Drain Valves; Purge Valves)

 

Boiler Drains shall be of bronze, brass or stainless steel construction.  Maximum working 

temperature shall be no less than 200

o

F and maximum working pressure shall be no less 

than 125 psi. 

 

Pressure Relief Valve 

The pressure relief valve shall be of bronze, brass or stainless steel construction with a 

pressure setting between 30psi and 150psi.  The pressure relief valve shall be set to 

discharge at a pressure below the maximum design pressure of all other components in the 

collector loop. 

 

Check Valve 

(A.K.A. Non-Return Valve)

 

The check valve may be a stand alone component or may be integral to the circulator 

pump.  The check valve shall be spring type of bronze, brass or stainless steel or polymer 

construction.  Maximum working temperature shall be no less than 200

o

F and maximum 

working pressure shall be no less than 125 psi. 

 

Air Vent 

The air vents shall be of bronze, brass or stainless steel construction.  Maximum working 

temperature shall be no less than 200

o

F and maximum working pressure shall be no less 

than 125 psi.   

 

Appendix A

Summary of Contents for SolaRay 2



















































Reviews: