background image

 

iv  

Using Forklifts 

Any persons operating a forklift must have an 
active recognized operator license.  

 

Note:   Before initializing forklift operation, 

verify that the lift is in a safe operating 
position. 

Ensuring Electrical Safety 

All electrical sources must be powered-off 
before installation, service, or repair of 
equipment occurs. 

 

Note:   Sundyne recommends that a Lock-

out/Tag-out program be followed prior 
to altering the equipment.  Locks or 
tags must be provided to warn 
employees that equipment is 
temporarily unavailable.  

Once all work has been completed, the person 
installing the lock or tag must remove it 
according to company procedure.  

Testing Equipment 

Prior to performing a test on newly installed, 
maintained, or repaired equipment; all personnel 
in the immediate area must be warned.  

 

Note:  Follow company procedures prior to 

equipment testing at all times. 

Using Chemicals 

Any chemicals to be used must be accompanied 
by a relevant material safety data sheet (MSDS), 
in accordance with government legislation.  If 
applicable, use chemical proof gloves.  

  

 

Note:   An eye wash station (or equivalent) 

should be available in the event of 
injury.  If any hazardous or flammable 
chemicals pass through the equipment, 
a complete decontamination of the 
equipment is required. 

Protection from Falling 

Fall protection and associated preventative 
measures 

are

 required when working on 

equipment located six feet or higher from the 
ground.  

 

Note:  Follow company fall prevention 

procedures prior to working on 
equipment. 

Preventative Machine Guards 

Preventative guards must remain in place on all 
equipment.  

 

Note:   Only remove the guards while 

performing maintenance or repair.  

 

Replace the guards immediately after working 
on the equipment and prior to start up. 

 

EXPLOSION/FIRE HAZARD  

Never use an acetylene torch, open flame, or 
heat to attempt to remove parts that have seized 
together in Sundyne equipment. Any residual 
process gas or liquid that is flammable can 
result in an explosion or fire with potential for 
serious injury or death. 

 

 

 

 

 

 

 

Summary of Contents for LMV-333




































































Reviews: