Sundstrom SR500EX How-To Download Page 3

Page: 3 / 18

SR500ex PAPR

—

How to

…prepare the

battery

New batteries must be charged before they are
used for the first time. On delivery, the battery
fitted in the fan unit is provided with protective
tape over the terminals. Remove the battery and
remove the tape.

Check that the gasket which is situated around
the contact plate opening underneath the
battery is intact.

Connect the battery to the battery charger.
Connect the charger plug to a wall socket.

N.B.! Main voltage 100-240 V

The charger carries out charging in four stages.

Yellow

LED. Battery analysis and

initiation.

Orange

LED. The battery is being charged

at maximum charging current.

Green

–

Yellow

Intermittent flashing

LED. Top of charging mode.

Green

LED. Charging completed.

Switches to maintenance charging mode.

When charging has been completed, pull the
plug out of the socket before separating the
battery from charger.

Summary of Contents for SR500EX


















Search results

Summary of Contents for SR500EX

Reviews:

Related manuals for SR500EX

Brands by name

Popular brands

Sundstrom SR500EX, How-To

Search results

Summary of Contents for SR500EX

Reviews:

Related manuals for SR500EX

Brands by name

Popular brands