2
WARNING
•
We highly recommend this product be installed by a qualified professional. Do not install if you have doubts regarding the
effectiveness or safety of an installation method.
•
Please do not begin installation until you have thoroughly read and understood these instructions. Failure to comply with
these instructions could result in damage to the product, or serious injury, or death.
•
Do not install if any parts are missing or defective. Do not attempt to replace with unapproved parts or materials or install
without all required parts.
•
This mount supports display mounting from VESA 200x200 up to 700X500.
•
This mount supports a maximum load of 79.5 kg (175 lb).
•
Ensure the ceiling will safely support the combined weight of the mount and your chosen display.
•
TV display should be removed from mount in situations of high wind exceeding 97 kph (60 mph).
•
All assembly fasteners and mounting plate attachment to ceiling should be inspected for signs of loosening or damage
after any strong wind event and at least once annually. If any fasteners have loosened, retighten. If any damage is
observed, remove mount from service.
•
The manufacturer does not accept responsibility for incorrect installation.
CAUTION:
These ceiling mounts are intended for use only with the maximum weight of 175 lbs (79.5 kg).
SPECIFICATIONS
BOX CONTENTS
TOOLS REQUIRED
•
Maximum Load:
79.5 kg (175 lb)
•
Ceiling plate assembly (1)
•
Power drill
•
Extension: 0.91 m (3 ft.)
•
Mounting head (1)
•
3/16
"
(5 mm) drill bit
•
Stainless steel mounting hardware
•
Adapter plate (1/2)
•
5/16
"
(8 mm) masonry bit
•
Pan/swivel range: 360°
•
TV arms (2/4)
•
1/2
"
(13 mm) wrench
•
Tilt range: +0°/-20°
•
0.91 m (3 ft.) fixed extension pole (1)
•
Phillips-head screwdriver
•
Weather-resistant coating
•
Hardware kit (1)
•
3/8
"
socket wrench
•
VESA patterns:
200×200 up to 700×500
•
7/16
"
socket wrench
HARDWARE KIT CONTENTS
M6 × 12 mm Phillips-
head screw (×4/8)
M8 × 16 mm Phillips-
head screw (×4/8)
Hex wrench 2.5 mm,
security (×2)
Hex wrench,
4 mm (×1)
M4 × 20 mm Phillips-
head screw (×4/8)
M5 × 30 mm Phillips-
head screw (×4/8)
M6 × 30 mm Phillips-
head screw (×4/8)
M8 × 20 mm Phillips-
head screw (×4/8)
M8 × 40 mm Phillips-
head screw (×4/8)
M8 carriage bolt (×4/8)
M8 nylon-insert
nut (×4/8)
M5 × 12 mm Phillips-
head screw (×4/8)
M6 × 20 mm Phillips-
head screw (×4/8)
Security wrench (×1)
M5 (16 × 5.3 × 1.5 mm)
metal washer (×4/8)
#14 × 2.5" lag screw (×4)
M8 (20.5 × 8.5 × 2 mm)
metal washer (×12/24)
Locking pin (×1/2)
M4/M5/M6 spacer:
12 mm (×4/8)
M6/M8 spacer:
17.8 mm (×4/8)
M5 × 5mm set screw,
security (×4)
M5 × 5 mm set screw (×4)
M4 × 12 mm Phillips-
head screw (×4/8)
M6 (17.8 × 6.5 × 1.5 mm)
metal washer (×4)
