background image

 

8

 

9. MOUNTING MICROWAVE TO WALL 

 

1.

 

Tape Wall Template on the wall. The top should be as close to the base of the cabinet as possible 
and should be kept in the middle. The top should be 1.8m from ground, 0.9m from cooking area. 

Note:

 if the front is lower than the back edge, make the top edge parallel with front edge of the 

cabinet. 

2.

 

Bore holes at A, B, C, D diameter 8mm (if not convenient, select different locations according to 
the mounting template). 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

1.

 

Tape the Top Template to the underside of the cabinet as indicated in figure1   

2.

 

In D and E of the attached figure, bore a hole 13mm 

3.

 

In F of the attached figure 2, bore a hole 38mm 

4.

 

Bore a hole along the broken line of the shading part of figure 2 

5.

 

Install the microwave according to the steps in Figures 7 & 8 on 
Page 5. 

at t ached 

f i gur e  1

f ast en  on  t he  ver t i cal  

f ace  of   t he  cabi net

762. 0000

C

D

1. past e on t he cabi net  wal l ,  t he t op shoul d be as appr oachi ng 

t he base of  t he cabi net  as possi bl e and t o be kept  i n t he mi ddl e

t he t op shoul d be 1. 8m  f r om gr ound,  0. 9m  f r om cooki ng ar ea.

not e:   i f   t he  f r ont   l ower   t han  t he  back  edge,   make t he t op edge

par al l el   wi t h  f r ont   edge  of   t he  cabi net .
2.  bor e hol es at  A, B, C, D di amet er  8mm (i f  not  conveni ent ,  sel ect
some ot her  pl ace of  t he at t ached f i gur e).

3. i nst al l   t he  oven  accor di ng  t o  t he  st eps  i n  t he  i nst al l at i on

book.

A

B

165. 0000

D

C

1. 8m at  l east  f r om 

gr ound

0. 9m at  l east  f r om cook 

ar ea

B

A

f i g. 15

762. 0000

at t ached 

f i gur e  2

hole

le

ft

1:  past e t he at t ached f i gur e 2 on t op of  t he cabi net  as 
i ndi cat ed  i n  f i gur e1(t ape  i t   r i ght f ul   l ocat i on,   cl ose  on  edge 

A,   t ake  car e  t o  be  i n  mi ddl e  of   i t .

2:  i n D,  and E of  t he at t ached f i gur e,  bor e a hol e 13mm

3:   i n  F  of   t he  at t ached  f i gur e2,   bor e  a  hol e  38mm

4:  bor e a hol e al ong t he br oken l i ne of  t he shadi ng par t  of  

t he  f i gur e  2.

5:   cont i nue  wi t h  t he  i nst al l at i on  t o  t he  i nst al l at i on  book.

B

13. 0000

A

φ

13mm hol e

D

power  cor d 

hol e

219 . 0000

18 0. 0000

wall

C

27 5. 0000

342. 0000

B

F

A

C

ri

gh

t

φ

13mm hol e

( scr ew 

hol e)

F

φ

38mm hol e

f i gur e  1

E

        Fig. 15 

Fig. 16 

Summary of Contents for SNM1501RAB










Reviews: