manualshive.com logo in svg

Sun Microsystems StorEdge 3000 Series, Best Practices Manual

Share
Download
Sun Microsystems StorEdge 3000 Series Best Practices Manual Download Page 12

xii

    Sun StorEdge 3000 Family Best Practices Manual

 

• March 

2007

Chapter

 

8

 describes a sample high-capacity configuration that includes both Sun 

StorEdge 3510 FC expansion units and Sun StorEdge 3511 SATA expansion units 
connected to a Sun StorEdge 3510 FC RAID array

 

in a way that maximizes reliability, 

availability, and serviceability.

Using UNIX Commands

This document might not contain information on basic UNIX

®

 commands and 

procedures such as shutting down the system, booting the system, and configuring 
devices. Refer to the following for this information:

■

Software documentation that you received with your system

■

Solaris™ operating environment documentation, which is at

http://docs.sun.com

Shell Prompts

Shell

Prompt

C shell 

machine-name

%

C shell superuser 

machine-name

#

Bourne shell and Korn shell 

$

Bourne shell and Korn shell superuser 

#

Summary of Contents for StorEdge 3000 Series























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands