Sun Microsystems StorageTek VSM GUI Page 45 Getting Started Manual Download

Page: 45 / 68

312651601 • Rev A

CH APT ER

Installing PTFs for VSM GUI

This chapter describes how to install the corrective service PTFs for VSM GUI, which

you can download from the Sun StorageTek Customer Resource Center at:

http://www.support.storagetek.com.

Note –

Before you install PTFs, you must install VSM GUI as described in “Installing

and Configuring the VSM GUI” on page 3.

For information on accessing the CRC, see “Customer Resource Center” on page xii.

Installing the PTFs

After you have downloaded the desired PTFs from the StorageTek CRC, install them

using the following procedure:

1. Ensure that you have customized the installation jobs as described in “Set Up the

SMP/E Environment and Install the Software” on page 13.

2. If necessary, modify member

V1RCV

Change the

SMPPTFIN

and

SMPHOLD

DDs to point to the downloaded data set names. If

there was no

HOLDDATA

downloaded, then remove the

SMPHOLD

DD and only receive

SYSMODS

3. Run member

V1RCV

RECEIVE

the VSM GUI PTFs.

4. If necessary, modify member

V2APPLY

Before running the apply job, review the output from the receive job for

HOLDDATA

, and

follow the instructions given for each held PTF. When the requirements are met, bypass

the hold condition for that held PTF in the apply job with the

BYPASS

parameter. Do

not

bypass

HOLDERROR

conditions.

5. Run member

V2APPLY

APPLY

the VSM GUI PTFs.

Summary of Contents for StorageTek VSM GUI





































































Search results

Summary of Contents for StorageTek VSM GUI

Reviews:

Related manuals for StorageTek VSM GUI

Brands by name

Popular brands

Sun Microsystems StorageTek VSM GUI, Getting Started Manual

Search results

Summary of Contents for StorageTek VSM GUI

Reviews:

Related manuals for StorageTek VSM GUI

Brands by name

Popular brands