manualshive.com logo in svg

Sun Microsystems SPARCcenter 2000, Installation Manual

Share
Download
Sun Microsystems SPARCcenter 2000 Installation Manual Download Page 48

4-6

SPARCcenter™ 2000/2000E Installation Manual—June 1996

4

Note – The following screen display is an example only. The actual message
displayed on the screen will vary with the software running on the system.

If POST indicates a hardware problem at this time, refer to the
SPARCcenter 2000 Service Manual for further instructions.

Note – If there is no OpenBoot PROM master board in the system, or if the
OBP master is replaced by an unprogrammed system board, the OpenBoot
program may prompt you to select a system board to become the new OBP
master. A terminal is necessary, both to see the OBP message, and to enter a
slot selection—the system is not hung, but will pause indefinitely until you enter a
selection. Refer to the SPARCcenter 2000 Service Manual for information about
system master board selection.

Note – When the system finishes booting for the first time —if there is no
appropriate server configuration file on the disk drive— it may be necessary to
prevent the JumpStart automatic configuration program from running. See
Section 3.3, “Precautions for JumpStart Automatic Installation.”

4.3 Interpreting Status LED Patterns

If there is no terminal on the system, basic system status information is
available on the front panel LEDs, as shown in Figure 4-5.

<<<< SPARCsystem 2000XX POST VX.X >>>>

...(various test messages)...

SPARCsystem 2000 Series (2 X XXXXXX), No Keyboard

ROM Rev. -.-, --- MB Memory installed, Serial #---.

Ethernet address -:-:--:-:--:--, Host ID: ------.

Summary of Contents for SPARCcenter 2000



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands