Sun Microsystems 805-1797-10 Installation And User Manual Download Page 41

Page: 41 / 65

TABLE C–1

qfe

Driver Parameter, Status, and Descriptions

(continued)

Parameter

Status

Description

100hdx_cap

Read only

Local transceiver capability of the
hardware

10fdx_cap

Read only

Local transceiver capability of the
hardware

10hdx_cap

Read only

Local transceiver capability of the
hardware

lp_autoneg_cap

Read only

Link partner auto negotiation
capability

lp_100fdx_cap

Read only

Link partner capability

lp_100hdx_cap

Read only

Link partner capability

lp_10fdx_cap

Read only

Link partner capability

lp_10hdx_cap

Read only

Link partner capability

instance

Read and write

Device instance

lance_mode

Read and write

Additional delay before
transmitting a packet

ipg0

Read and write

Additional delay before
transmitting a packet

Defining the Current Status

The read-only parameters described in Table C–2 explain the operational mode of the
interface. These parameters define the current status.

Configuring the Quad FastEthernet Device Driver Parameters

Summary of Contents for 805-1797-10


































































Search results

Summary of Contents for 805-1797-10

Reviews:

Brands by name

Popular brands

Sun Microsystems 805-1797-10, Installation And User Manual

Search results

Summary of Contents for 805-1797-10

Reviews:

Brands by name

Popular brands