Sun Microsystems 805-1797-10 Installation And User Manual Download Page 40

Page: 40 / 65

Driver Parameter Values and Definitions

This section describes the parameters and settings for the

qfe

device driver. Table

C–1 lists these parameters.

TABLE C–1

qfe

Driver Parameter, Status, and Descriptions

Parameter

Status

Description

transceiver_inuse

Read only

Defines the current status

link_status

Read only

Defines the current status

link_speed

Read only

Defines the current status

link_mode

Read only

Defines the current status

ipg1

Read and write

Inter-packet gap parameter

ipg2

Read and write

Inter-packet gap parameter

use_int_xcvr

Read and write

Operational mode parameter

pace_size

Read and write

Operational mode parameter

adv_autoneg_cap

Read and write

Operational mode parameter

adv_100fdx_cap

Read and write

Operational mode parameter

adv_100hdx_cap

Read and write

Operational mode parameter

adv_10fdx_cap

Read and write

Operational mode parameter

adv_10hdx_cap

Read and write

Operational mode parameter

autoneg_cap

Read only

Local transceiver auto negotiation
capability

100fdx_cap

Read only

Local transceiver capability of the
hardware

Sun Quad FastEthernet PCI Adapter Installation and User’s Guide

♦

Revision A, August 1997

Summary of Contents for 805-1797-10


































































Search results

Summary of Contents for 805-1797-10

Reviews:

Brands by name

Popular brands

Sun Microsystems 805-1797-10, Installation And User Manual

Search results

Summary of Contents for 805-1797-10

Reviews:

Brands by name

Popular brands